Universal Air Tools UT8704 - Manual

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Important
Operator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules
the tool to the air line system without incorporating an easy to
reach and operate air shut off valve. The air supply should be
lubricated. It is strongly recommended that an air filter,
regulator, lubricator (FRL) is used as shown in Figure 1 as this
will supply clean, lubricated air at the correct pressure to the
tool. Details of such equipment can be obtained from your
supplier. If such equipment is not used then the tool should be
lubricated by shutting off the air supply to the tool,
depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a
teaspoonful (5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air
supply and run tool slowly for a few seconds to allow air to
circulate the oil. If tool is used frequently lubricate on daily basis
and if tool starts to slow or lose power. It is recommended that
the air pressure at the tool whilst the tool is running is 90 p.s.i./
6.3 bar. The tool can run at lower and higher pressures with the
maximum permitted working air pressure of 100 p.s.i./7 bar.
Manufacturer/Supplier Product Type
RPM
Cycles Per Min
Model No/Nos Serial No (if any)
Product Nett Weight
lbs
Kg
Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M No
Page No 1
30 mm Belt Sander
UT8704
4.4
2.0 3/8 10 30 10
13,000
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Work Stations
The tool should only be used as a hand held hand operated tool.
It is always recommended that the tool is used when standing
on a solid floor. It can be used in other positions but before any
such use the operator must be in a secure position having a firm
grip and footing and be aware of the safety rules to be obeyed
when using the sander.
Foreseen Use of the Tool
The tool is designed for the purpose of cleaning or sanding of
materials using a continuous abrasive belt. Belts are available in
various grades to suit fine finishing or fast material removal.
Do not use the tool for any other purpose than that for which it
was designed. Do not modify this tool for any other use or for
its use as a belt sander without first consulting the manufacturer
or the manufacturer’s authorised distributor.
Tel No Fax No
(01494) 883300 (01494) 883237
Noise Level
Sound Pressure Level 89.0 dB(A)
Test Method
Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Sound Power Level 100.0 dB(A)
Vibration Level
Test Method
Tested in accordance with ISO
standard 8662/1
Less than 2.5
Metres / Sec²
Personal Safety Equipment
Use - Safety Glasses
Yes
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Yes
Use - Ear Protectors
Air Pressure
Recommended Working
6.3
bar
90
PSI
Recommended Minimum
n/a
bar
n/a
PSI
Maximum
7.0
bar
100
PSI
Putting Into Service
Air Supply
Use a clean lubricated air supply that
will give a measured air pressure at
the tool of 90 p.s.i./6.3 bar when
the tool is running with the trigger/
lever fully depressed. Use
recommended hose size and length.
It is recommended that the tool is
connected to the air supply as
shown in figure 1. Do not connect