Lincoln Electric IM874 VANTAGE 300 - Manual (Page 26)

C-1 ACCESSORIES C-1
FIELD INSTALLED OPTIONS /
ACCESSORIES
K2641-2 FOUR WHEELED STEERABLE YARD TRAILER
For in plant and yard towing. Comes standard with a Duo-
Hitch™, a 2” Ball and Lunette Eye combination Hitch.
K2636-1 TRAILER - Two-wheeled trailer with optional fend-
er and light package. For highway use, consult applicable
federal, state, and local laws regarding possible additional
requirements. Comes standard with a Duo-Hitch™, a 2” Ball
and Lunette Eye combination hitch. Order:
K2636-1 Trailer
K2639-1 Fender & Light Kit
K2640-1 Cable Storage Rack
K1898-1 SPARK ARRESTOR - Easily mounts to standard
muffler.
K704 ACCESSORY SET - Includes 35 ft. (10m) of elec-
trode cable and 30 ft. (9.1m) of work cable, headshield,
work clamp electrode holder. Cables are rated at 400
amps, 100% duty cycle.
K857 25 ft (7.6m) or K857-1 100 ft. (30.4m) REMOTE
CONTROL
Portable control provides same dial range as the output con-
trol on the welder. Has a convenient 6 pin plug for easy con-
nection to the welder.
K2467-1 - Digital weld meters kit with easy to read digital
meters for volts and amps. Easy to install.
K802N POWER PLUG KIT
Provides four 120 volt plugs rated at 20 amps each and one
dual voltage, full KVA plug rated at 120/240 volts, 50 amps.
K802R POWER PLUG KIT
Provides four 120 volt plugs rated at 15 amps each and one
dual voltage, full KVA plug rated at 120/240 volts, 50 amps.
T12153-9 50 AMP, 120/240V POWER PLUG (1-Phase)
T12153-10 50 AMP, 240V POWER PLUG (3-Phase)
K1816-1 FULL KVA ADAPTER KIT
Plugs into the 120/240V NEMA 14-50R receptacle on the
case front (which accepts 4-prong plugs) and converts it to
a NEMA 6-50R receptacle, (which accepts 3-prong plugs.)
For connection of Lincoln equipment with NEMA 6-50 Plug.
WIRE FEEDER OPTIONS
K449 LN-25 - Includes internal contactor for across the arc
operation (no control cable). Provides “cold” electrode until
gun trigger is pressed. Includes gas solenoid.
K1870-1 LN-15 Across the Arc Wire Feeder.
Portable, lightweight, compact CC/CV unit for flux-
cored and MIG welding. Includes Gas Solenoid,
adjustable flow meter and internal contactor. For 10-
15 lb. (4.5-6.8kg) spools.
Magnum Gun and Magnum Gun Connector Kit are
required for gas-shielded welding. Innershield Gun is
required for gasless welding.
K126-2 Magnum 350 Innershield Gun
K1802-1 Magnum 300 MIG Gun (for LN-25)
K470-2 Magnum 300 MIG Gun (for LN-15, Includes
Connector Kit)
K466-10 Connector Kit (for LN-15, K470-2)
K1500-1 Gun Receiver Bushing (for LN-15 & K126-2)
K487-25 Magnum SG Spool Gun
Hand held semiautomatic wire feeder. Requires SG
Control Module and Input Cable.
K488 SG Control Module (For Magnum Spool Gun)
The Interface between the power source and the
spool gun. Provides control of the wire speed and gas
flow. For use with a spool gun.
K691-10 Input Cable (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-
type connection, separate 115V NEMA receptacles
and output stud connections.
Note: See Wire Feeder IM manuals for appropriate
Drive Roll and Guide Tubes.
TIG OPTIONS
K1783-9 Pro -Torch® PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with
valve for gas flow control. 25 ft. (7.6m) length.
KP509 Magnum Parts Kit for PTA-26V TIG Torch
Magnum Parts Kit provides all the torch accessories
you need to start welding. Parts kit provides collets,
collet bodies, a black cap, alumina nozzles and tung-
stens in a variety of sizes, all packaged in an easy to
carry reclosable sack.
K870 Foot Amptrol®
K963-3 Hand Amptrol®
K2347-1 Precision TIG 185 Ready-Pak(For AC TIG)
K2350-1 Invertec® V205-T AC/DC One-Pak™ Package
(For AC TIG)
PLASMA CUTTING
K1580-1 Pro-Cut 55
Cuts mild steel using the 3-phase AC generator power
from the engine driven welder. Accepts 3-phase or 1-
phase input power. Requires the K1816-1 Full KVA
adapter kit, if connected for 1-phase input power.
VANTAGE 300