Anthro Fit Adjusta Unit 30/36/48 Assembly Instructions - Manual (Page 4)

3 /
4
” Wood Screw
325-5106-00
Support Screw
325-5010-00
Step 8
(requires Worksurface to be 12” from floor)
Place the Mechanism onto the Worksurface Assembly.
Align the Mechanism Flanges with the predrilled holes
on the Worksurface underside.
Secure the Mechanism to the Worksurface using a total of
twelve Wood Screws.
Align the six holes of the Brake Assembly with those on
the Worksurface. It may be necessary to depress the
Paddle while manipulating the Brake over the predrilled
Worksurface holes.
Secure the Brake Assembly using a total of six Wood Screws.
Anthro Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841 anthro.com
Step 3
Place your Fixed Worksurface onto the floor with the
predrilled holes facing upward.
Position the Small Support Brackets onto the Fixed
Worksurface and align two of the holes on each Support
with the predrilled holes on the Worksurface. Loosely
secure each Small Support to the Worksurface using two
Wood Screws per Support.
Step 5
Determine the best height for your Fixed Worksurface.
These instructions will place your Fixed Worksurface 31”
from the floor using the standard 3” Casters.
For a final Fixed Worksurface height that is lower than
31”, adjust one hole down for each inch of variance
desired.
NOTE: Your Fixed Worksurface location may be changed
after your Adjusta Unit has been completely assembled by
repeating Steps 6 and 7.
Step 4
Place the Back Trough onto the Fixed Worksurface,
between the installed Support Brackets (from Step 3).
Align the two Threaded holes on each end of the Back
Trough with those on both Support Brackets. Carefully,
thread one Button Head Screw through the Support
Bracket, into the Back Trough. Repeat for remaining three
Button Head Screws.
Insert two Wood Screws through the two remaining Holes
on the Back Trough flange (which should be aligned with two
predrilled holes on the Worksurface) and tighten into place.
3 /
4
” Wood Screw
325-5106-00
3 /
4
” Wood Screw
325-5106-00
( 1 /
4
-20 X .50”) Button Head Screw
325-5003-00
Small Support
Bracket X
FIRST: Install the Button Head Screws
SECOND: Install the Wood Screws
Back Trough
Back Trough
Flange
NOTE: Make certain
to install the Back
Trough in front of the
Support Brackets
Threaded
holes
31”
Adjusta Fixed
Worksurface
Adjusta Caddy has
approximately 11”
of travel
Support Screw
325-5010-00
Step 6
Attach a rear Vertical Leg by installing two Support Screws
through the Small Support Bracket Y into Holes 1 & 3
from the top (non-coped end).
Attach a front Vertical Leg to Holes 1 & 3 using the same
procedure.
Step 7
Attach the remaining Vertical Legs to the Small Support
Bracket X using the same procedure used in Step 6.
NOTE: Make certain to install the Vertical Legs into the same
holes used in Step 6.
Small Support
Bracket Y
Hole 1=31” Final Worksurface Height
Top
(non-coped)
end
Bottom
(coped)
end
Hole 3
Hole 1
Hole 3
Small Support
Bracket X
Hole 1
Hole 3
Top
(non-coped)
end
Bottom
(coped)
end
(12” high surface shown shaded)
Paddle
Brake
Mechanism Flanges
FAJ30zz/xx3, FAJ36zz/xx3 & FAJ48zz/xx3
300-5196-00
Small Support
Bracket X
Small Support
Bracket Y
Wood Screw
Support Screw
Support Screw
Wood Screw