Anthro Large AnthroCarts 48W Assembly Instructions - Manual (Page 2)

Anthro ® Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062
Step 1
These Instructions will cover both the H12xx & H13xx
48” Wide AnthroCart assembly. Before proceeding,
please review the Assembly Instructions of all Anthro
Products you purchased and are planning to include
in this installation.
These instructions will place your Shelf 28” from the
floor using the standard 2
3 /
8
” Castors.
The approximate time to complete the assembly of your
48” Wide AnthroCart is 45 minutes.
Step 3
Attach all four Shelf Supports to the Shelf.
Begin by first installing a Shelf Clamp into the Shelf
notch. Be sure the pointed “Barbs” face towards the
outer Shelf edge.
Next, slide a Shelf Support into the recesses of the
Shelf Clamp and Shelf. Push in as far as possible.
Finally, secure with a Clamp Screw.
www.anthro.com
Step 4
Position both Bridge Side Gussets onto the Shelf
underside as shown.
Align the predrilled holes on the underside of the Shelf
with those on the Gussets and secure into place using
a total of four Wood Screws per Gusset.
NOTE: Make certain the Bridge Side Gussets are oriented
so the “flanges” face toward the inside of the Cart.
Step 5
Attach the “front” Vertical Legs by loosely installing one
Support Screw through a “front” Shelf Support into Hole
2 from the top (non-coped end) of a Leg.
Next, loosely install two Support Screws through a Side
Gusset into a corresponding Leg.
Repeat for remaining “front” Vertical Leg and Side Gusset.
Step 7
Place the Bridge Pan onto the Shelf between the
“rear” Vertical Legs. Secure the Pan to the Shelf by
first installing three Wood Screws through the Pan
“flange” into the Shelf.
Next, insert a Bracket Screw from the “rear” of the
Cart through the Pan and carefully thread into a Pan
End Bracket. Finally, repeat for the remaining Bracket
Screws and Pan End Bracket.
Questions? 1-800-325-3841
Wood Screw
325-5106-00
Support Screw
325-5010-00
Step 2
Determine the best height for your Shelf. Generally,
a 28” high work surface works well for most people
and equipment.
For a final Shelf height that is higher or lower than 28”,
refer to the illustration shown at right to determine
which holes to attach your Shelf.
Your Shelf locations may be changed after your
Cart has been completely assembled by repeating
Steps 5 & 6.
H12xx with 2 3 /
8
” Castors
H12xx4 with 4” Castors
H12xxGL with Glides
Hole 2=28”
Hole 3=27” (measured from the non-coped end)
Hole 4=26”
Hole 2=29”
Hole 3=28”
Hole 4=27”
Hole 2=25”
Hole 3=24”
Hole 4=22”
Coped end
28”
29”
25”
1 /
4
-20 X .375” Bracket Screw
325-5149-00
First
Next
Finally
Clamp Screw
325-5086-00
“Barbs”
H12xx & H13xx
48”Wide AnthroCart shown with 2 3 /
8
” Castors
Add 1” to overall height for 4” Castors
Subtract 3” from the overall height for Glides
28” High Shelf
Wood Screw
325-5106-00
48” Wide AnthroCart
Assembly Instructions
Both Bridge Side Gusset
“flanges” face toward the
inside of the Cart.
Predrilled holes
NOTE: tighten all Wood and Bracket Screws after
they have ALL have been successfully installed.
Step 6
Loosely attach the “rear” Vertical Legs using the same
procedure described in Step 5.
Next, position a Pan End Bracket against a “rear” Vertical
Leg. Secure into place by loosely installing three Support
Screws through the Bracket into Holes 3, 4 & 5 from the
top of a ‘rear” Leg.
Repeat for remaining “rear” Vertical Leg and Pan End Bracket.
Support Screw
325-5010-00
“Front”
Shelf Support
“Rear”
Shelf Support
Hole 2
Top (non-coped) end
Pan “Flange”
Bracket Screw
Wood Screw
Bridge Pan
NOTE: make certain the Pan End Brackets are oriented
so the “PEM” Nut is facing the “front” of the Cart.
Hole 2
Bottom
(coped)
end