TREND IQ3..._..._XNC_... - Manual (Page 7)

7 IQ3../.../XNC/... Controller/Interface Installation Instructions TG200911 Issue 1/D 03/09/07
Installation Instructions IQ3../.../XNC/...
3 Insertion/Replacement of Battery (if battery required)
O
I
Switch Off
1
Isolate I/O
2
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 + 0 + 0 + 0 + 0 + 0
1 2 3 1 + 0
0 V 24 V 24 V 34 35 36 12 37 38 39 13 40 41 42 14 A 31 32 33 P 11 43 44 45
15
46 47 48
16 100-240 V OK RX P 0 P 0 P 0 P 0 P 0 P 0
O
I
O
I
WARNING: The
connecting leads
may be connected
to supplies. Isolate before
touching.
Open Panel 3
A 0 V 24 V 24 V 34 35 36 12 37 38 39 13 40 41 42 14 A 31 32 33 P 11 43 44 45 15 46 47 48 16 100-240 V OK RX P 0 P 0 P 0 P 0 P 0 P 0
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 19 20 21 7 22 23 24 8 25 26 27 9 28 29 30 10 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 1 2 3 1 + 0
WARNING: Opening the panel may expose
dangerous voltages.
417-IEC-5036
Remove Auxiliary Board Cover 4
a
b
c
d
CR 2032
CR 2032
Remove battery (if replacing battery) 5
Replace Auxiliary Board Cover
7
Warning: The lithium battery must not be recharged,
disassembled, burnt or short circuited.
Misuse may cause explosion or fire.
Dispose of carefully (see Section 4,
Disposal, below). Refer to Health and
Safety Executive Guidance Note GS43.
+
Insert new battery 6
CR2032 3 V
a b
9 Reconnect Supply to I/O Close Panel
8
A 0 V 24 V 24 V 34 35 36 12 37 38 39 13 40 41 42 14 A 31 32 33 P 11 43 44 45 15 46 47 48 16 100-240 V OK RX P 0 P 0 P 0 P 0 P 0 P 0
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 19 20 21 7 22 23 24 8 25 26 27 9 28 29 30 10 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 1 2 3 1 + 0
10
Switch On
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 + 0 + 0 + 0 + 0 + 0
1 2 3 1 + 0
0 V 24 V 24 V 34 35 36
12
37 38 39
13
40 41 42
14 A
31 32 33 P
11
43 44 45
15
46 47 48
16 100-240 V
OK RX P 0 P 0 P 0 P 0 P 0 P 0
O
I
O
I
O
I
IQ3.../.../XNC/.../USA/UL/24
is UL rated as ‘UL916 listed
open energy management
equipment’.