TREND IQ3..._..._XNC_... - Manual (Page 4)

4 IQ3../.../XNC/... Controller/Interface Installation Instructions TG200911 Issue 1/D 03/09/07
IQ3../.../XNC/... Installation Instructions
19K2
0
1
9K6 9k6
19k2
2 Installation - Configuration
Continue Installation 1
IQ3../.../XNC/... Installation Instructions TG200911 sheet 1
IQ3xact Installation Instructions TG200766
IQ3xcite Installation Instructions TG200626
Complete IQ3../.../XNC/... installation instructions sheet 1
and IQ3xact installation instructions up to section 4 step 19,
or IQ3xcite Installation Instructions up to section 4 step 20.
Select Terminator Switch Position
2
If /SER/.., serial interface auxiliary board, fitted
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 19 20 21 7 22 23 24 8 25 26 27 25 26 27 9 28 29 30 10 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0
1 2 3 1 + 0 + 0
0V 24 V 24 V 34 35 36 12 37 38 39 37 38 39 13 40 41 42 14 A 31 32 33 P 11 43 44 45 43 44 45 15 46 47 48 46 47 48 16 100-240 V OK RX P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0
TX
RX
RTS/TXEN
CTS/RXEN
RS485 RS232
terminator in circuit terminator out of circuit
RS485 4 wire
RS485 2 wire RS422
terminator in either position
RS232
Set current loop Network Baud Rate and Address 3
If /LAN/.., IQ system current loop Lan auxiliary board, fitted
4 5 6 2 7 8 9 3 10 11 12 4 13 14 15 5 16 17 18 6 19 20 21 7 22 23 24 8 25 26 27 9 28 29 30 28 29 30 10 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0
1 2 3 1 + 0 + 0
0V 24 V 24 V 34 35 36 12 37 38 39 13 40 41 42 14 A 31 32 33 P 11 43 44 45 15 46 47 48 16 100-240 V OK RX OK RX P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0 P 0
TX RX OK
a, Set address switch
1 2 4 8 16 32 64
0
1
e.g. Address = 2 + 16 = 18 NOT SET
SET
Address = A
=A*
IQ3../LAN/XNC/...
*Note that the IQ3../LAN/XNC/... may also use addresses
for its virtual CNC, and for its local supervisor CNC which
should also be unique on the Lan.
=A /
=A /
=A /
address
1, 4 to 9, 11 to 119
0, 2, 3,10 or >119
b, Set baud rate switch
current loop Lan baud rate = B
= B
= B
= B
= B
e.g. Baud Rate = 19k2