Sunex Tools SX232B - Manual (Page 4)

SX232B Rev. 08/29/07
Air Supply...
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI at
the tool while running free. Higher pressure (over 90 psig; 6.2 bar)
raises performance beyond the rated capacity of the tool; which will
shorten tool life because of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water
in the air line will cause damage to the tool. Drain the air tank
daily. Clean the air inlet filter screen on a weekly schedule. The
recommended connection procedure can be viewed in the
above figure.
The air inlet used for connecting air supply, has standard 1/4" NPT.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions and
be tightly secured.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no air line
oiler is used, run a half ounce of oil through the tool. The oil can
be inserted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool. The amount of oil
to be used is 1/2 oz. Overfilling will cause a reduction in the power
of the tool.
Other factors outside the tool may cause loss of power or erratic
action. Reduced compressor output, excessive drain on the air line,
moisture or restrictions in air pipes or the use of hose connections
of improper size or poor condition may reduce air supply. Grit or
gum deposits in the tool may cut power and may be corrected by
cleaning the air strainer and flushing out the tool with gum solvent
oil or an equal mixture of SAE #10 oil and kerosene. If outside
conditions are in order and the tool continues erratic action or low
power, disconnect tool from hose and take tool to your nearest
authorized service center.
Operation...
When using the grinder, be careful not to exert excessive force. Too
much force may be hazardous if it causes the cutting tool spindle to
bend or break.
The burning of the work piece or excessive speed reduction
indicates too much force being applied. Changing to a free cutting
tool may be better for the desired rate of speed and stock removal.
Avoid hazardous condition by making sure there is sufficient
gripping force on the spindle of the cutting tool by placing the
spindle 7/16" or more inside the collet.
Limited Warranty...
sunex internAtionAl, inc. wArrAnts to its custoMers thAt the coMpAny’s sunex tools ® brAnded products Are free froM defects in
worKMAnship And MAteriAls.
Sunex International, Inc. will repair or replace its Sunex Tools
® branded products which fail to give satisfactory service due to defective workmanship or materials,
based upon the terms and conditions of the following described warranty plans attributed to that specific product. This product carries a ONE-YEAR warranty.
During this warranty period, Sunex Tools ® will repair or replace at our option any part or unit which proves to be defective in material or workmanship.
other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made
by anyone other than Sunex Tools ® or its authorized warranty service centers. The foregoing obligation is Sunex Tools’ sole liability under this or any implied
warranty and under no circumstances shall we be liable for any incidental or consequential damages.
note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Return equipment or parts to Sunex Tools ® , or an authorized warranty service center, transportation prepaid. Be certain to include your name and address,
evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools
® . This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools ® products regardless of whether or not the product is
still covered by a warranty plan.
shipping Address: sunex tools
® • 315 hawkins rd. • travelers rest, sc 29690
Mailing Address: sunex tools ® • p.o. box 4215 • greenville, sc 29608
%SBJO%BJMZ
3FHVMBUPS 0JMFS 2VJDL$PVQMFS -FBEFS
)PTF
/JQQMF
%P/PU*OTUBMM
2VJDL$PVQMJOH
)FSF
/JQQMF
'JMUFS
"JS4VQQMZ
8IJQ)PTF
Operating Instructions • Warning Information • Parts Break­down
SX232B_manual_082907.indd 4 8/31/07 1:58:46 PM