Sunex Tools SX235KTB - Manual (Page 4)

SX235KTB 4 Rev. 05/02/02
Nipple
Operating Instructions • Warning Information • Parts Breakdown
Air Supply...
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measure 90 PSI at the
tool while running free. Higher pressure and unclean air will
shorten the tool’s life because of faster wear and may create a
hazardous condition.
Water in the air line will cause damage to the tool. Drain the air tank
daily. Clean the air inlet filter screen on at least a weekly schedule.
The air inlet, used for connecting air supply, has standard 1/4" NPT
American Thread.
Line pressure should be increased to compensate for unusually long air
hoses (over 25 feet). Minimum hose diameter should be 1/4" I.D.
and fittings should have the same inside dimensions
Lubrication...
Lubricate the tool daily with a good grade of air tool oil. If no air
line oiler is used, run a teaspoon of oil through the tool. The oil can
be squirted into the tool air inlet, or into the hose a the nearest
connection to the air supply, then run the tool. A rust inhibitive oil is
acceptable for air tools.
WARNING: After an air tool has been lubricated, oil will discharge
through the exhaust port during the first few seconds of operation.
The exhaust port must be covered with a towel before applying air
pressure to prevent serious injury.
Operation...
Always place a chisel in the hammer and hold the tool down to the
work before operating. Damage to the tool
or the retainer may result if this precaution is not followed.
The chisel retainer (Ref. No. 17) is not designed for complete safety
against accidental release of cutters or hammers. To avoid injury,
the throttle (trigger) must never be depressed unless the chisel is held
firmly against the work place. When tool is not in actual use, the
chisel must be removed. During operation, safety goggles should
ALWAYS be used to guard against flying rust and chips. When
using tool, regulate the speed so that the chisel is not being driven
out of the cylinder. If piston is allowed to strike the cylinder wall,
internal damage will result.
To change chisel, pull back on spring hook and insert chisel.
Release spring hook.
To regulate air, turn air regulatorknob out for maximum air
pressure and in for minimum.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS
THAT THE COMPANY’S SUNEX TOOLS
® BRANDED PRODUCTS
ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools ®
branded products which fail to give satisfactory service due to
defective workmanship or materials, based upon the terms and
conditions of the following described warranty plans attributed to
that specific product. This product carries a ONE-YEAR warranty.
During this warranty period, Sunex Tools will repair or replace at our
option any part or unit which proves to be defective in material or
workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising
from alteration, abuse, misuse, damage and does not cover any
repairs or replacement made by anyone other than Sunex Tools or its
authorized warranty service centers.The foregoing obligation is
Sunex Tools’ sole liability under this or any implied warranty and
under no circumstances shall we be liable for any incidental or
consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. Return equipment or parts to Sunex
Tools, or an authorized warranty service center, transportation
prepaid. Be certain to include your name and address, evidence of
the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to
Sunex Tools. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state. Repair kits
and replacement parts are available for many of Sunex Tools
products regardless of whether or not the product is still covered by
a warranty plan.
Shipping Address: Sunex Tools • 315 Hawkins Rd.
Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215
Greenville, SC 29608