Sunex Tools SX113 - Manual (Page 4)

Rev. 04/24/03 SX113 4
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no
air line oiler is used, run a teaspoon of oil through the
tool. The oil can be squirted into the tool air inlet or into
the hose at the nearest connection to the air supply, then
run the tool.
Operation...
This ratchet wrench is rated at 3/8" USS bolt size. Rating
must be down graded for spring U bolts, tie bolts, long
cap screws, double depth nuts, badly rusted conditions
and spring fasteners as they absorb much of the impact
power. When possible, clamp or wedge the bolt to
prevent springback.
NOTE: Actual torque on a fastener is directly related to
joint hardness, tool speed, condition of socket and the
time the tool is allowed to impact.
Use the simplest possible tool-to-socket hook up. Every
connection absorbs energy and reduces power.
NOTE: Soak rusted nuts in penetrating oil and break rust
seal before removing with ratchet wrench. If nut does not
start to move in three to five seconds, use a larger size
ratchet wrench. Do not use ratchet wrench beyond rated
capacity as this will drastically reduce tool life.
Nipple
Operating Instructions • Warning Information • Parts Breakdown
Air Supply...
Tools of this class operate on a wide range of air pressures.
It is recommended that air pressure of these tools measures
90 PSI at the tool while running free. Higher pressure (over
90 psig; 6.2 bar) raises performance beyond the rated
capacity of the tool which will shorten tool life because of
faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or
water in the air line will cause damage to the tool. Drain the
air tank daily. Clean the air inlet filter screen on at least a
weekly schedule. The recommended hookup procedure can
be viewed in the above figure.
The air inlet used for connecting air supply, has standard
1/4" NPT. Line pressure should be increased to compensate
for unusually long air hoses (over 25 feet). Minimum hose
diameter should be 3/8" I.D. and fittings should have the
same inside dimensions and be tightly secured.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY’S SUNEX TOOLS ®
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools
® branded products which fail to give satisfactory service due to
defective workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed
to that specific product. This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will repair or
replace at our option any part or unit which proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover
any repairs or replacement made by anyone other than Sunex Tools or its authorized warranty service centers.The foregoing
obligation is Sunex Tools’ sole liability under this or any implied warranty and under no circumstances shall we be liable for any
incidental or consequential damages.
Note:
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. Return equipment or parts to Sunex Tools, or an authorized warranty service center,
transportation prepaid. Be certain to include your name and address, evidence of the purchase date, and description of the
suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state. Repair kits and replacement parts are available for many of Sunex
Tools products regardless of whether or not the product is still covered by a warranty plan.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SX113_OpMan_042303 11/5/03 11:45 AM Page 4