FIREPOWER MS-10UD-7 - Manual (Page 3)

DF-52416:C • 05/12/2009 — Page 3 of 4
Initiating Device Circuits – TB4 (and TB 6 on MS-10UD-7
only):
• Alarm Zones 1 - 5 on TB 4 (MS-5UD-3 and MS-10UD-7).
• Alarm Zones 6 - 10 on TB6 (MS-10UD-7 only).
• Supervised and power-limited circuitry.
• Operation: All zones Style B (Class B).
• Normal Operating Voltage: Nominal 20 VDC.
• Alarm Current: 15 mA minimum.
• Short Circuit Current: 40 mA max.
• Maximum Loop Resistance: 100 ohms.
• End-of-Line Resistor: 4.7K ohm, 1/2 watt (P/N 71252 UL-
listed).
• Standby Current: 2 mA.
Refer to the Fire•Lite Device Compatibility Document for listed
compatible devices.
Notification Appliance Circuits – TB5 (and TB 7 on MS-
10UD-7 only):
• Four NACs
• Operation: Style Y (Class B)
• Special Application power
• Supervised and power-limited circuitry
• Normal Operating Voltage: Nominal 24 VDC
• Maximum Signaling Current: 3.0 A for MS-5UD-3, 2.5 A
maximum per NAC; 7.0 A for MS-10UD-7(E), 3.0 A maxi-
mum per NAC.
• End-of-Line Resistor: 4.7K ohm, 1/2 watt (Part #71252)
• Max. Wiring Voltage Drop: 2 VDC
Refer to the Fire•Lite Device Compatibility Document for com-
patible listed devices.
Form C Relays – TB8:
• Relay 1 (factory default programmed as Alarm Relay)
• Relay 2 (factory default programmed as fail-safe Trouble
Relay)
• Relay 3 (factory default programmed as Supervisory Relay)
Special Application Resettable Power – TB9:
• Jumper selectable by JP31 for resettable or nonresettable
power.
• Operating voltage: 24 VDC nominal.
• Maximum available current: 500 mA - appropriate for pow-
ering four-wire smoke detectors.
• Power-limited circuit.
Refer to the Fire•Lite Device Compatibility Document for listed
compatible devices.
Remote Sync Output - TB2: Remote power supply synchro-
nization output, only required for the MS-5UD-3. 24 VDC nom-
inal special application power. Maximum current is 40 mA.
End-of-Line Resistor: 4.7K ohm. Supervised and power-lim-
ited circuit.
Product Line Information
MS-5UD-3: Five-zone, 24-volt Fire Alarm Control Panel
(includes backbox, FLPS-3 power supply, technical manual,
and a frame & post operating instruction sheet).
MS-10UD-7: Ten-zone, 24-volt Fire Alarm Control Panel
(includes backbox, FLPS-7 power supply, technical manual,
and a frame & post operating instruction sheet).
MS-10UD-7E: Same as above with 240 VAC FLPS-7.
IPDACT, IPDACT-2/2UD Internet Monitoring Module:
Mounts in bottom of enclosure with optional mounting kit (PN
IPBRKT). Connects to primary and secondary DACT tele-
phone output ports for internet communications over customer
provided ethernet internet connection. Requires compatible
Teldat Visoralarm Central Station Receiver. Can use DHCP or
static IP. (See data sheet df-52424 for more information.)
IPBRKT: Mounting kit for IPDACT in common enclosure.
IPSPLT: Y Adaptor option to allow connection of both panel
dialer outputs to one cable input to IPDACT (sold separately).
OPTIONAL MODULES
CAC-5X: Optional (Class A) Converter Module. Converts Style
B (Class B) Initiating Device Circuits to Style D (Class A); and
Style Y (Class B) Notification Appliance Circuits to Style Z
(Class A). Connects to J2 on the MS-5UD-3 and MS-10UD-
7(E) main circuit board and to J7 on the MS-10UD-7(E).
NOTE: Two Class A Converter Modules are required for the ten-
zone panel.
4XTMF: Transmitter module. Provides a supervised output for
local energy municipal box transmitter and alarm and trouble
reverse polarity. Includes a disable switch and disable trouble
LED. A module jumper option allows the reverse polarity circuit
to open with a system trouble condition if no alarm conditions
exists. Mounts to the main circuit board connectors J4 and J5.
COMPATIBLE ANNUNCIATORS
ANN-80: Remote LCD Annunciator. Mimics the information
displayed on the FACP’s LCD. Red. (For white, order: ANN-
80-W.)
ANN-LED: LED Annunciator with three LEDs for each zone:
Alarm, Trouble, and Supervisory. Mounts in the DP-51050(B)
dress panel. (For white, order: ANN-80-W.)
ANN-RLED: LED Annunciator with three alarm (red) indica-
tors for up to 30 input zones or addressable points. (See DF-
60241).
ANN-RLY: Relay module. Mounts inside the cabinet. Provides
ten Form C relays.
ANN-S/PG: Serial/parallel printer gateway. Provides a connec-
tion for a serial or parallel printer.
ANN-I/O: Driver module. Provides connections to a user-sup-
plied graphic annunciator.
ACCESSORIES
DP-51050: Optional dress panel. Restricts access to the sys-
tem wiring while allowing access to the membrane switch
panel.
BB-26: Battery backbox, holds up to two 25 AH batteries and
CHG-75.
BB-55: Battery backbox, holds up to two 25 AH batteries.
TR-CE: Optional trim-ring for semi-flush mounted cabinets.
PRN-6F: UL listed printer.