Pach and Company AeGIS 4000_4000RT Manual User Manual

Page 23

DELETE ALL

CALL

FORWARDING

PHONE

NUMBER ON

FUNCTION

CODE 70, 71 and

ENABLE OR

DISABLE

AUTOMATIC

CALL

FORWARDING

“One Short Beep” and select another
Function Number (71 – 72).

Step 4

• Enter 0 then #, you will hear “One

Short Beep” and phone number
programmed is deleted or

• Enter 1 then #, you will hear “No

Beep” and enter a new call
forwarding phone number up to
11- digit, you will hear “One Short
Beep”.

Step 5

Enter another Function Code

to delete another Call Forwarding or to
program another parameter otherwise
press

∗ to exit and you will hear

“Three Short Beeps”.

Entering The Programming Mode:
Press 0 and # simultaneously then
release. If you are in the programming
mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.

Step 3

Enter 76 then #, you will

hear “One Short Beep”.

Step 4

Enter another Function Code

to program another parameter
otherwise press

∗ to exit and you will

hear “Three Short Beeps”.

Step 1

Entering The Programming

Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Step 5

•

Press “0” and #, you will hear “One

Short Beep” and phone number
programmed is deleted or

• Press “1” then press # you will hear

“No Beep” and enter a new phone
number up to 11-digit then press #,
you will hear “One Short Beep”.

Step 6

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps”

Step 1

Pick up the phone and wait

for a dial tone.

Step 2

Press # # and you will hear

“One Short Beep”.

Step 3

Press # and you will hear

“One Short Beep”.

Step 4

Enter the Function Code 76

then press #, you will hear “One Short
Beep”.

Step 5

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps”.

Step 1

Pick up the phone and wait

for a dial tone.

Step 2

Press # # and you will hear

“One Short Beep”.

Step 3

Press # and you will hear

“One Short Beep”.

Step 4

Press 87 then #, you will

hear “One Short Beep”.

Step 4

Enter the Function Code

number “71” or “72” then press #, you
will hear “Two Long Beeps”; means a
phone number is already programmed,
proceed to step 5. If you hear “No
Beep”, means no phone number is
programmed, press

∗ and continue

step 4 or proceed to step 6.

Step 5

• Press “0” and #, you will hear “One

Short Beep” and phone number is
deleted.

• Press “1” then press # you will hear

“No Beep” and enter a new phone
number up to 11-digit then press #,
you will hear “One Short Beep”.

Step 6

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps”.

Step 1

Call to the AeGIS 4000

system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and yo

will

hear “One Short Beep”.

• “One Long Beep”, the master code

is rejected and the connection will be
disconnected.

Step 3

Press # to enter into the pro-

gramming mode and you will hear
“One Short Beep” or

∗∗ to hang-up

the call.

Step 4

Enter the Function Code 76

then press #, you will hear “One Short
Beep”.

Step 5

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps”.

Step 1

Call to the AeGIS 4000

system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and you will
hear “One Short Beep”.

• “One Long Beep”, the master code

is rejected and the connection will be
disconnected.

Function

Local Programming

Premise Phone

Remote Phone

Pach and Company

Page 14

AeGIS 4000

Chapter 3. Programming