Pach and Company AeGIS 4000_4000RT Manual User Manual

Page 21

Pach and Company

Page 12

AeGIS 4000

Chapter 3. Programming

DIRECT CALL

FORWARDING

IS USED IF

A DEDICATED

PHONE LINE IS

USED OR IF

YOU WANT TO
FORWARD THE

CALL

MANUALLY.

NOTE:

INTERCOM

MODE IS

DISABLED IF

A PHONE

NUMBER IS

PROGRAMMED

ON FUNCTION

CODE 70

Step 1

Entering The Programming

Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat step
1. Should your master code become
lost or forgotten see Reset Master
Code.

Step 3

Enter 65 then #, you will

hear “One Short Beep”.

Step 4

Enter another Function Code

to program another parameter; other-
wise press

∗ to exit and you will hear

“Three Short Beeps”.

Step 1

Entering The Programming

Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten Reset Master
Code.

Step 3

Enter 70 then #, you will

hear “No Beep”.

Step 4

Enter the phone number you

want to forward the call up to 11-digit
then press #, you will hear “One Short
Beep”.

Step 5

Enter another Function Code

to program another parameter; other-
wise press

∗ to exit and you will hear

“Three Short Beeps”.

Step 1

Press 0 and

∗

simultaneously then release.

Step 2

Press 0 then # to delete

telephone number, you will hear
“Three Short Beeps”. Now, the
AeGIS 4000 is reset to “Intercom
Mode”.

Step 3

Press # and you will hear

“One Short Beep”.

Step 4

Enter 65 then press #, you

will hear “One Short Beep”.

Step 5

Enter another function code

to program different parameter or exit
the program by pressing

∗ ∗ and you

will hear “Three Short Beeps”.

Step 1

Pick up the phone and wait

for dial tone.

Step 2

Press # # and you will hear

“One Short Beep”.

Step 3

Press # and you will hear

“One Short Beep”.

Step 4

Enter 70 then press #, you

will hear “No Beep”.

Step 5

Enter the non-indexed call

forwarding phone number up to 11-
digit you will hear “One Short Beep”.

Step 6

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three
Short B

eeps”.

Step 1

Pick up the phone and wait

for dial tone.

Step 2

Press # # and you will hear

“One Short Beep”.

Step 3

Press 6 and you will hear

“Three Short Beeps”, and the system
disconnects the call.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and you will
hear “One Short Beep” .

• “One Long Beep”, the master code

is rejected and the connection will be
disconnected.

Step 3

Press # to enter into the

programming mode and you will hear
“One Short Beep” or

∗∗ to hang-up

the call.

Step 4

Enter 65 then press #, you

will hear “One Short Beep”.

Step 5

Enter another function code

to program different parameter or exit
the program by pressing

∗ ∗ and you

will hear “Three Short Beeps”.

Step 1

Call to the AeGIS 4000

system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked.“Two
Short Beeps”, the gate is unlocked.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and you will
hear “One Short Beep” .

• “One Long Beep”, the master code

is rejected and

the connection will

be disconnected.

Step 3

Press # to enter into the

programming mode and you will hear
“One Short Beep” or

∗∗ to hang-up

the call.

Step 4

Enter 70 then press #, you

will hear “No Beep”.

Step 5

Enter the non-indexed call

forwarding phone number up to 11-
digit you will hear “One Short Beep”.

Step 6

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps.

Step 1

Call to the AeGIS 4000

system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and you will
hear “One Short Beep”.

Function

Local Programming

Premise Phone

Remote Phone

Program

Direct Call

Forwarding

Delete Direct

Call

Forwarding