English – CAME BX-241 User Manual
Page 11
- Trimmer TCA = Automatic closing time: 1" to 120";
- Trimmer AP.PARZ. = Partial opening time: 1" to 15".
- Trimmer SENS.= amperometric sensitivity adjustment
1 ON - Automatic closure enabled
2 ON - "Open-stop-close-stop" radio control and/or button function enabled (with plug-in radiofrequency board)
2 OFF - "Open-close-reverse" radio control and/or button function enabled (with plug-in radiofrequency board)
3 ON - "Only open" radio control and/or button function enabled (with plug-in radiofrequency board)
4 ON - "Maintained action" operation enabled
5 ON - Pre-fl ashing (aperture and closure) enabled
6 ON - Obstacle detection device (motor of limit position) enabled
7 OFF - Re-aperture in closure phase enabled; activate safety device (2-C1), if not set the dipswitch to ON
8 OFF - "Stop" button enabled; activate safety device (1-2), if not set the dipswitch to ON
9 OFF - "Partial-stop" enabled; activate safety device (2-C3), if not set the dipswitch to ON
10
Not used
ON
OFF
/.
+ T.P.A. -
+ T.P.A. -
+ T.A.C. -
+ T.A.C. -
+ SENS. -
+ SENS. -
&# &
-
&!
.
#/.42
/,
!2$
#
/
.
42
/
,
"/
!2
$
•
••
••
••
••
••
••
•
•
••
••
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
••
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••••
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
• • • • •• • •
%
0 # #
6 !#
,4 ,4
,
,
"!44%29
$
#
"
!
02/'2!-
#(
!&!&
11
A
ll t
h
e d
at
a a
n
d i
n
fo
rm
at
io
n c
o
n
ta
in
ed h
er
ei
n
i
s c
o
n
si
d
er
ed
s
u
b
je
ct to c
h
an
g
e a
t a
n
y t
im
e a
n
d a
t o
u
r d
is
cr
et
io
n
ENGLISH
2)
The AF board should
AL WAYS be in sert ed when the
pow er is off.
1) On AM transmitters operating at 433.92 MHz (TOP and
TAM series), position the jumper connection on circuit card
AF43S as shown on the sheet.
Frequency/MHz
Radiofrequecy Transmitter
FM 26.995
AF130
TFM
FM 30.900
AF150
TFM
AM 26.995
AF26
TOP
AM 30.900
AF30
TOP
AM 433.92
AF43S / AF43SM
TAM / TOP
AM 433.92
AF43SR
ATOMO
AM 40.685
AF40
TOUCH
6.8 Adjustments
6.7 Function selections
7.1 Prepare the radio board (AF)
7 Installation procedure of the transmitter for remote control
Read the three steps below before beginning installation procedures:
- prepare the radio board (paragraph 7.1);
- procedure for codifying the transmitter (paragraph 7.2);
- memorizing the code on the command board (paragraph 7.3).
TOP
TAM
AF - Radio board
Motherboard