Atec Tinius-Olsen-H1KS - Manual (Page 7)

7
Key Features
• PC control via high speed RS232 using
ASCII and super high speed binary modes
• Force accuracy of 0.5% of applied load
across the load cell display range
• 32 bit precision motor controller
• Displacement resolution of 0.0001 mm
(T series in binary mode)
• Speed resolution of 0.001 mm/min
• 150% mechanical overload on load cells
• 20% digital load tare while maintaining
full load cell capacity
• Automatic motor alarms monitor over/
under voltage, current and temperature
• Built-in intelligent active force and
displacement alarm system
Fig 39. Testing the tensile strength of the
seam on a shaving foam canister
Fig 38. Machine being used to determine
the strength of a flexible geo material
Specifications:
Load measurement accuracy: +/- 0.5% of indicated load from 2% to 100% capacity; extended range down to 1%
capacity with accuracy of 1% of indicated load
Position measurement accuracy: +/- 0.01% of reading or 0.001 mm, whichever is greater
Speed accuracy: +/- 0.005% of set speed
Operating temperature range: 32 to 100 degrees F (0 to 38 degrees C)
Storage temperature range: 14 to 115 degrees F (-10 to 45 degrees C)
Humidity range: 10% to 90% non-condensing, wet bulb method
Power: standard optional voltages 220/240VAC, 50-60 Hz, 2000W; power must be free of spikes and surges exceeding
10% of the nominal voltage
Technical Specifications
Notes: 1. Load weighing system meets or exceeds the requirements of the following standards: ASTM E4, EN 10002-2, BS 1610, DIN 51221, ISO 7500-1. Tinius Olsen
recommends that systems are verified at installation in accordance with ASTM E4 and ISO 75001. 2. Strain measurement system meets or exceeds the requirements of
the following standards: ASTM E83, EN 10002-4, BS 3846 and ISO 9513. 3. These models conform to all relevant European CE Health and Safety Directives EN 50081-1,
580081-1, 73/23/EEC, EN 61010-1 4. Specifications are subject to change without notice.
lbf 2000 5000 10,000
kN 10 25 50
kg 1000 2500 5000
in 16 16 16
mm 405 405 405
in 43 43 43
mm 1100 1100 1100
in/min 0.00004 to 40 0.00004 to 40 0.00004 to 20
mm/min 0.001 to 1000 0.001 to 1000 0.001 to 500
lbf 1000 2000 5000
kN 5 10 25
in/min 20 20 10
mm/min 500 500 250
in/min 0.00004 to 40 0.00004 to 40 0.00004 to 20
mm/min 0.001 to 1000 0.001 to 1000 0.001 to 500
in/min 0.00004 to 40 0.00004 to 40 0.00004 to 20
mm/min 0.001 to 750 0.001 to 1000 0.001 to 500
in 63 x 26 x 18 63 x 26 x 18 64 x 29 x 20
mm 1600 x 650 x 450 1600 x 650 x 450 1613 x 720 x 500
lb 255 265 310
kg 115 120 140
CLEARANCE
BETWEEN COLUMNS
LOAD CELLS
MAXIMUM CROSSHEAD
TRAVEL
TESTING SPEED
RANGE
CAPACITY AT
MAXIMUM SPEED
MAXIMUM SPEED
AT CAPACITY
JOG SPEED
RETURN SPEED
DIMENSIONS
H x W x D
CAPACITY
MODEL H10K H25K H50K
WEIGHT
Measurement direct from ballscrew – fully
auto scaling of single measurement range
Rapid change, low profile Z type load cells
with digital encoding for automatic recognition
and scaling available – 10kN, 5kN, 2.5kN,
1kN, 500N, 250N, 100N, 50N, 10N, 5N
Rapid change, low profile Z type load cells
with digital encoding for automatic recognition
and scaling available – 25kN, 10kN, 5kN,
2.5kN, 1kN, 500N, 250N, 100N, 50N, 10N, 5N
Rapid change, low profile Z type load cells
with digital encoding for automatic recognition
and scaling available – 50kN, 25kN, 10kN, 5kN,
2.5kN, 1kN, 500N, 250N, 100N, 50N, 10N, 5N
Measurement direct from ballscrew – fully
auto scaling of single measurement range
Measurement direct from ballscrew – fully
auto scaling of single measurement range