Atec Wayne-Kerr-3255B - Manual (Page 4)

Wayne Kerr’s policy is one of continuous development and consequently the product may vary in detail from the description and specification in this publication.
www.waynekerrtest.com [email protected]
February 2006 A4
Technical data sheet
UK
Wayne Kerr Electronics
Vinnetrow Business Park
Vinnetrow Road, Runcton
Chichester, West Sussex
PO20 1QH, UK
Tel: +44 1243 792200
Fax: +44 1243 792201
USA
Wayne Kerr Electronics
165L New Boston Street
Woburn
MA 01801-6201 USA
Tel: +1 781 938 8390
Sales: (800) 933 9319
Fax: +1 781 933 9523
General data
Input specification
Power supply
230 V AC ±10% or
115 V AC ±10% (selectable)
50 to 400 Hz
150 VA maximum consumption
Display
High contrast monochrome LCD
320 x 240 dot with back lighting.
Visible area 115 x 86mm.
Viewing angle 45°
Measurement connections
4 front panel BNC sockets
4-wire (Kelvin) measurements with screen at ground potential
Equivalent circuit symbols on screen
Remote control (option)
Conforms with GPIB IEEE-488.2 and SCPI 1992.0
Printer output
Centronics/parallel printer port
Environmental conditions
Temperature range
Storage -40°C to 70°C
Operating 0°C to 40°C
Full Accuracy 15°C to 35°C
Altitude up to 2000m
Relative humidity: up to 80% non-condensing
Installation category: II (in accordance with IEC664)
Pollution degree: 2 (mainly nonconductive)
This equipment is intended for indoor use only in non-explosive,
non-corrosive atmosphere.
Safety
Complies with the requirements of EN61010-1
EMC
Complies with EN50081-1, EN50082-1 generic emissions and
immunity standards by meeting with the requirements of
EN55022, IEC801.2, IEC801.3 and IEC801.4
Mechanical (approx. overall)
Height 150 mm (6″)
Width
440 mm (17 3 /
8
″)
Depth 520 mm (20 1 /
2
″)
Weight 11 kg (24 lb 4 oz)
Order codes and options
Description Order code
3255BL Inductance Analyzer – 200 kHz 1J3255BL
Supplied with user manual and power cable
3255B Inductance Analyzer – 500 kHz
1J3255B
Supplied with user manual and power cable
3255BQ Inductance Analyzer - 1 MHz 1J3255BQ
Supplied with user manual and power cable
Options
/A 1 mA to 1 A internal DC bias
/B GPIB (IEEE-488) interface
/
D1 Bin handler (cannot be fitted with /D2)
/ D2 Bin handler opto-coupled (cannot be fitted with /D1
Auxiliary unit
5A DC bias unit 3265B/5A 1J3265B/5A
10A DC bias unit 3265B/10A
` 1J3265B/10A
20A DC bias unit 3265B/20A
1J3265B/20A
(Not compatible with 3255BL)
25A DC bias unit 3265B/25A
1J3265B/25A
(Not compatible with 3255BL)
All auxiliary units are supplied with user manual, power cable,
spare fuses, 4 x BNC to BNC links and daisy chain
link.
Accessories
Description Order code
1009 DC Bias Fixture 1J1009
High current lead set for 1009 5-328-2005
Kelvin clips (fine jaws). 1EVA40100
Kelvin clips (large jaws) 1EVA40180
4-terminal lead set 1EV1505
SMD Tweezers 1EVA40120
Bus bars 4-324-6009
Rack mounting kit, 3U x full width 1EXA20230
(Unit needs rear support)