Atec Sunrise-Telecom-SUNSET-T3 - Manual (Page 3)

Fractional T1 (SW311)
Error measurements, channel configuration verification
Nx64 kbps, Nx56 kbps, N=1 to 24
Sequential, alternating, or random channels
Set Tx and Rx channels independently
Auto scan and auto configure to any FT1 order for active channels
Selectable idle channel code, 7F or FF hex
Requires SW310
ESF and SLC-96 Datalink send and Receive (SW312)
ESF Datalink
Read and Send T1.403 message on FDL (PRM and BOM)
Automatic HDLC protocol handling
YEL ALM, LLB ACT, LLB DEA, PLB ACT, PLB DEA
T1.403 24 hour PRM collection per 15 min interval
SLC-96 Datalink
Send and receive message
WP1, WP1B, NOTE formats
Alarms, switch-to-protect, far end loop
To Telcordia TR-TSY-000008 specifications, modes I and III
SLC-96 FEND loop
Requires SW310
CSU/NI Emulation (SW313)
Graphical indication of signal status
Simultaneous display of T1 line measurements
Automatic generation of AIS
Loopbacks
Responds to remote loopback commands, in-band and out-of-
band (ESF datalink T1.403)
Establish Line and payload loopback from keypad
Requires SW310
Voice Frequency Capability (SW320)
General: Talk/listen with volume control, 24 channel signaling bit
display, control signaling bits, view channel data,
µ
/A law to DS3
or DS1/E1 ports
Specify trunk type: E&M, ground/loop start, FXO, FXS, user defined
Specify supervision on idle channels
Basic Transmission Impairment Measurements: Level, frequency, C-
message noise, C-notched noise, 3 kHz flat filter noise, signal to
noise with 1004 Hz tone. Generate 50 to 3950 Hz
±
1 Hz, 1 Hz
steps, +3 to -60 dBm, 1 dB steps. Requires SW321.
Addressing
DTMF/MF/DP dialing, programmable dial number up to 32 digits,
10 stored numbers, programmable transmit level -5 to -25 dBm
MF/DTMF dialing: Specify dial period, silent period from 50 ms to
999 ms
DP dialing: Specify %break from 40 to 60, interdigit period from
200 ms to 900 ms
Measure MF/DTMF high/low frequency, level, twist, digital time,
interdigital time
Measure DP pulses per second, %break
Requires SW322
ISDN PRI Call Setup and Analysis (SW323)
D-channel message monitor
Filter type: Call reference, caller number, called number
Voice and data call setup and receive
Talk/listen for voice calls
56k, 64k data rates
Data patterns: 2047, 511, 127, 63, All 1s, All 0s, or 8-bit user pattern
Programmable called and caller numbers, B-channel number, NSF
code, NSF type
NT, TE emulation
Programmable D-channel number
AT&T 5ESS and Northern Telecom DMS-100 compatible
On-screen table for optional call feature programming
Requires SW310
GENERAL
SW options upgradeable via software in-field cartridge replacement
Printer: Print every 2 to 99 minutes, print at end of measurement,
print on error/alarm events, print screen alphanumerics
Size: 4 x 2.4 x 10.5" [10.5 x 6 x 27 cm]
Weight: 2.8 lb [1.3 kg]
SS300e chassis only
Built-in NiMH rechargeable battery pack
Battery operating time: 90 min nominal. AC operation with 100
to 240 VAC, 50/60 Hz universal charger.
Operating temperature: 32˚F to 122˚F [0˚C to 50˚C]
Storage temperature: -4˚F to 158˚F [-20˚C to 70˚C]
Humidity: 5% to 90% noncondensing
ORDERING INFORMATION
Test Set
SS300e SunSet T3 Chassis
Includes SunSet T3 Chassis, 100 VAC to 240 VAC Universal
Battery Charger, 6-cell NiMH battery, SunSet T3 User’s
Manual, SunSet T3 Field Manual, Software Cartridge,
Instrument Stand. Software Cartridge includes basic T3
testing operations.
Software Options
SW301 DS3 FEAC
Provides control and analysis of the DS3 FEAC data link in
C-bit parity framing format.
SW302 Remote Control
Allows menu-driven remote control of basic test functions
using a dumb terminal or personal computer equipped with
VT100 terminal emulation software. Includes printer cable
and null modem adapter.
SW303 Maintenance Switch, Performance Monitoring NIU, RAMP,
Looping Repeaters. Provides menu-driven support for the
Westell & Teltrend looping repeaters, Maintenance Switch,
and Performance Monitoring NIU, including the RAMP
feature. Requires SW310.