Atec LeCroy-Wavepro7000 Series - Manual (Page 2)

Specifications
Vertical System WavePro 7000 WavePro 7100 WavePro 7200 WavePro 7300
Analog Bandwidth @ 50 Ω (-3 dB) 1 GHz 1 GHz 2 GHz 3 GHz
Rise Time (Typical) 400 ps 400 ps 225 ps 150 ps
Input Channels 4
Bandwidth Limiters 25 MHz; 200 MHz
Input Impedance 50 Ω; 1 MΩ//11pF typical (using PP005A probe)
Input Coupling 1 MΩ: AC, DC, GND; 50 Ω: DC
Maximum Input Voltage 50 Ω: 5 Vrms, 1 MΩ: 100 Vmax (peak AC: ≤5 KHz + DC)
Channel-Channel Isolation 250:1 at same V/div setting, 40:1 at 3 GHz
Vertical Resolution 8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity 50 Ω: 2 mV – 1 V/div fully variable; 1 MΩ: 2 mV – 2 V/div fully variable
DC Gain Accuracy ±1.5% of full scale; ±1% (typical)
Offset Range 50 Ω: ±700 mV @ 2-4.99 mV/div
±1.5 V @ 5-100 mV/div
±10 V @ .102-1 V/div
1 MΩ: ±700 mV @ 2-4.99 mV/div
±1.5 V @ 5-100 mV/div
±20 V @ 0.102-2 V/div
Offset Accuracy ±(1.5% of full scale + 0.5% of offset value + 2 mV)
Horizontal System
Timebases Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
Time/Division Range 20 ps/div – 10 s/div
Math & Zoom Traces 4 independent zoom and 4 math/zoom traces standard;
8 math/zoom traces available with XMAP (Master Analysis package) or XMATH (Advanced Math package)
Clock Accuracy ≤ 10 ppm @ 0–40 °C
Time Internal Accuracy ≤ 0.06 / SR + (10 ppm * Reading) (rms)
Sample Rate & Delay Time Accuracy ± 10 ppm ≤ 10 s interval
Jitter Noise Floor 2 ps rms @ 100 mV/div (typical)
Trigger & Interpolator Jitter ≤ 2.5 ps (typical)
Channel-Channel Deskew Range ±4.5 ns
External Clock 30 MHz – 1 GHz; 50 Ω impedance; applied at the auxiliary input
Acquisition System
Single-Shot Sample Rate/Ch 5 GS/s 10 GS/s 10 GS/s 10 GS/s
2 Channel Max 10 GS/s 20 GS/s 20 GS/s 20 GS/s
Random Interleaved Sampling (RIS) 200 GS/s for repetitive signals: 20 ps/div – 1 µs/div
Maximum Trigger Rate 150,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time ≤ 6 µs
Maximum Acquisition Points/Ch 4 Ch / (2 Ch) 4 Ch / (2 Ch) Sequence Mode
Standard 500k / 1M 1M / 2M 500 segments
M – Memory Option 4M / 8M 4M / 8M 1,000 segments
L – Memory Option — 8M / 16M 5,000 segments
VL – Memory Option — 16M / 32M 10,000 segments
XL – Memory Option — 24M / 48M 20,000 segments
Acquisition Processing
Averaging Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES) From 8.5 to 11 bits vertical resolution
Envelope (Extrema) Envelope, floor, roof for up to 1 million sweeps
Interpolation Linear, Sin x/x
Triggering System
Modes Normal, Auto, Single, and Stop
Sources Any input channel, External, Ext X10, Ext/10, or line; slope and level unique to each source (except line trigger)
Coupling mode DC50 Ω, GND, DC1MΩ, AC1MΩ
Pre-trigger delay 0–100% of horizontal time scale
Post-trigger delay 0–10,000 divisions
Hold-off by time or events Up to 20 s or from 1 to 99,999,999 events
Internal trigger range ±5 div from center
Max trigger frequency 1 GHz w/Edge Trigger; 1 GHz w/Edge Trigger; 2 GHz w/Edge Trigger; 3 GHz w/Edge Trigger;
750 MHz w/SMART Trigger 750 MHz w/SMART Trigger 750 MHz w/SMART Trigger 750 MHz w/SMART Trigger
Basic Triggers
Edge/Slope/Line Triggers when signal meets slope and level condition
SMART Triggers ®
State or Edge Qualified Triggers on any input source only if a defined state or edge occurred on another input source.
Delay between sources is selectable by time or events.
Dropout Triggers if signal drops out for longer than selected time between 2 ns and 20 s.
Pattern Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input).
Each source can be high, low, or don’t care.The high and low level can be selected
independently. Triggers at start or end of the pattern.
SMART Triggers
with Exclusion Technology
Glitch Triggers on positive or negative glitches with widths selectable from 600 ps to 20 s or on intermittent faults.
Signal or Pattern Width Triggers on positive or negative pulse widths selectable from 600 ps to 20 s or on intermittent faults.
Signal or Pattern Interval Triggers on intervals selectable between 2 ns and 20 s.