Atec Panametrics-Olympus-Omniscan-MX2 - Manual (Page 12)

48 Woerd Avenue, Waltham, MA 02453, USA, Tel.: (1) 781-419-3900
12569 Gulf Freeway, Houston, TX 77034, USA, Tel.: (1) 281-922-9300
505, boul. du Parc-Technologique, Québec (Québec) G1P 4S9, Tel.: (1) 418-872-1155
1109 78 Ave, Edmonton (Alberta) T6P 1L8
www.olympus-ims.com
[email protected] OmniScan_MX2_EN_201203 • Printed in Canada • Copyright © 2012 by Olympus NDT.
*All specifications are subject to change without notice.
All brands are trademarks or registered trademarks of their respective owners and third party entities.
is ISO 9001 and 14001 certified.
Compatible with the Following Inspection Codes:
The OmniScan MX2 is compatible with standard industry inspection codes, including, but not limited to:
ASME Section V, Article 4 AWS
All ASME phased array code cases API 1104 and API RP2X
ASTM E2700-09 CEN EN 583-6
ASTM E2491-06 BSI BS7706
… and more
OmniScan MX2 Mainframe Specifications
Overall dimensions
(W x H x D) 325 mm x 235 mm x 130 mm
(12.8 in. x 9.3 in. x 5.1 in.)
Weight 5 kg (11 lb), including module and one battery
Data Storage
Storage devices
SDHC card, most standard USB storage devices,
or fast Ethernet
Data file size 300 MB
I/O Ports
USB ports 3
Speaker out Yes
Video output Video out (SVGA)
Ethernet 10/100 Mbps
I/O Lines
Encoder
2-axis encoder line (quadrature, up, down, or
clock/direction)
Digital input 4 digital TTL inputs, 5 V
Digital output 4 digital TTL outputs, 5 V, 15 mA
Acquisition on/off
switch
Remote acquisition enabled TTL, 5 V
Power output line
5 V, 500 mA power output line
(short-circuit protected)
Alarms 3 TTL, 5 V, 15 mA
Analog output 2 analog outputs (12 bits) ±5 V in 10 kΩ
Pace input 5 V TTL pace input
Display
Display size 26.4 cm (10.4 in.) (diagonal)
Resolution 800 pixels x 600 pixels
Brightness 700 cd/m 2
Number of colors 16 million
Type TFT LCD
Power Supply
Battery type Smart Li-ion battery
Number of batteries
1 or 2 (battery chamber accommodates two
hot-swappable batteries)
Battery life Minimum 6 hours with two batteries
Environmental Specifications
Operating temperature
range 0 °C to 45 °C; 0 °C to 35 ºC with 32:128 PA
(32 ºF to 113 ºF; 32 ºF to 95 ºF with 32:128 PA)
Storage temperature
range
–20 °C to 60 °C (–4 ºF to 140 ºF) with batteries
–20 °C to 70 °C (–4 ºF to 158 ºF) without bat-
teries
Relative humidity
0% to 85% noncondensing
No air intake; designed for IP66
Shockproof rating Drop-tested according to MIL-STD-810G 516.6
Phased Array Module Specifications
(Applies to OMNI-M-PA32128)
Overall dimensions
(W x H x D) 244 mm x 182 mm x 57 mm
(9.6 in. x 7.1 in. x 2.1 in.)
Weight 1.2 kg (2.6 lb)
Connectors 1 OmniScan connector for phased array probes
Number of focal laws 256
Probe recognition Automatic probe recognition
Pulser/Receiver
Aperture 32 elements
Number of elements 128 elements
Pulser
Voltage 45 V or 90 V per element
Pulse width Adjustable from 30 ns to 500 ns, resolution of 2.5 ns
Pulse shape Negative square wave
Output impedance Less than 30 Ω
Receiver
Gain 0 dB to 74 dB, maximum input signal 1.25 Vp-p
Input impedance 50 Ω
System bandwidth 0.53 MHz to 21 MHz (–3 dB)
Beamforming
Scan type Sectorial and linear
Group quantity Up to 8
Active elements 32
Elements 128
Data Acquisition
Digitizing frequency 100 MHz (10 bits)
Maximum pulsing rate Up to 10 kHz (C-scan)
Data Processing
Number of data points Up to 8,000
Real-time averaging 2, 4, 8, 16
Rectifier RF, full wave, halfwave +, halfwave –
Filtering
Low-pass (adjusted to probe frequency), digital filtering
(bandwidth, frequency range)
Video filtering Smoothing (adjusted to probe frequency range)
Data Visualization
A-scan refresh rate Real time: 60 Hz
Data Synchronization
On internal clock 1 Hz to 10 kHz
On encoder On 1 or 2 axes
Programmable Time-Corrected Gain (TCG)
Number of points 16 (1 TCG curve per channel for focal laws)
Alarms
Number of alarms 3
Conditions Any logical combination of gates
Analog outputs 2
OmniScan MX2 Specifications