Atec Quadtech-6100-Plus - Manual

USES:
• Production and Compliance Testing of
Appliances, Instruments and Information
Technology Equipment in Accordance
with UL, CSA, IEC, TUV and Other
Standards such as EN60335, UL60950,
EN61010 and CSA C22.2 No. 1010.1
• Transformer Electrical Safety Testing
• Electric Motor Safety Testing
• Power Supply Safety Testing
• Verification of the Ground Connection on
Products with a Three Prong Power Cord
FEATURES:
• Twin Port - Simultaneous Hipot & GB
• Built-in 20A Hipot/Line Leakage Scanner
• Output Voltage to 5kV AC and 6kV DC
• Ground Bond Testing to 30A AC (to 40A
with Optional Transformer)
• Insulation Resistance Measurements from
100kΩ to 50GΩ
• Earth, Enclosure & Patient Line Leakage
Current Measurements to 9.999mA
• Open/Short Circuit Detection Mode
• Pause Mode with Message Capability
• Continuous Leakage Current Monitoring
• Programmable Trip Current to 40mA AC
and 12mA DC
• Programmable Ramp, Dwell & Test Times
• Storage of 100 Test Setups, 50 Steps Each
• Front Panel Lockout via Password
• Standard RS-232 & Remote I/O Interfaces
• Optional IEEE-488, Printer Interfaces
• Optional CaptivATE Automation
Software for G6100 Plus
Introduction
The Guardian 6100 Plus is the industry’s first production safety analyzer with
simultaneous Hipot and Ground Bond capability providing a dramatic savings in
test time. Six instruments in one, the G6100 Plus provides AC Hipot, DC Hipot,
Insulation Resistance, Leakage Current/Functional Run, Ground Bond and
Open/Short measurements from a single test connection. Versatile and packed with
features, the G6100 Plus is a cost effective solution for the full spectrum of electri-
cal safety compliance testing.
Description
Twin Port Technology: This patented feature allows for simulataneous Ground Bond and
Hipot Testing. Decrease test time and increase device through-put.
Leakage Current: With 20A input current capability, Leakage Current can be measured
from 0.1µA to 9.999mA. Perform Functional Run Tests while monitoring the Voltage,
Current or Power plus perform Earth, Enclosure and Patient leakage testing in 8 possible
modes including Normal, Reverse Line, Single Fault Normal and Single Fault Reverse.
Ground Bond: With test current from 1A to 30A in 0.1A steps and programmable current
limits, test time, frequency and open circuit no load voltage, the G6100 Plus provides full
GB testing capability. A 40Amp GB option is also available.
AC Hipot: AC dielectric testing over the voltage range from 50V to 5000VAC RMS. The
maximum leakage current of 40mA RMS is ideal for testing devices with high leakage cur-
rents such as power supplies which have large filter or “Y” capacitors for noise reduction.
DC Hipot: DC dielectric testing from 50V to 6000VDC with a resolution of 1V. Leakage
current can be continuously monitored from 0.1µA to 12mA DC.
Insulation Resistance: The G6100 Plus is capable of measuring IR from 100k to 50GΩ
with test voltage from 50V to 1000VDC in 1V steps.
Open/Short Circuit Detection Mode: Avoid false pass results by checking for Open and
Short connections and ensure that the DUT is properly connected not shorted.
Optional Scanners: Increase the number of test channels for multi-point or multi-device
testing by adding an external scanner to the G6100 Plus. Add up to 8HV channels or a com-
bination of HV and GB channels with just one external scanner.
Standard Interfaces: The Remote I/O and RS-232 interfaces provide remote control and
serial data collection capability for automated applications.
Guardian
6100 Plus
Safety Analyzer
for Electronics Production & Compliance Testing
Hipot Testers • LCR Meters • Cable Testers • AC/DC Programmable Power Sources
• Megohmmeters • Milliohmmeters
For more detailed information on
specifications, pricing and special
purchase, rent and lease options,
contact us at:
www.quadtech.com
800-253-1230