Optical interfaces, Ftb-8115, Sonet/sdh test module – Atec EXFO-FTB-8115 User Manual
Page 6
FTB-8115
SONET/SDH Test Module
Optical Interfaces
The following section provides detailed information on all supported optical interfaces.
Notes
a. In order not to exceed the maximum receiver power level before damage, an attenuator must be used.
b. SFP compliance: The FTB-8115 selected SFP shall meet the requirements stated in the “Small Form-Factor Pluggable (SFP) Transceiver
Multisource Agreement (MSA)”.
The FTB-8115 selected SFP shall meet the requirements stated in the “Specification for Diagnostic Monitoring Interface for Optical Xcvrs”.
155.52 Mbit/s ± 4.6 ppm
622.08 Mbit/s ± 4.6 ppm
2.48832 Gbit/s ± 4.6 ppm
2.48832 Gbit/s ± 100 ppm
622.08 Mbit/s ± 100 ppm
155.52 Mbit/s ± 100 ppm
1260 to 1360 nm
1430 to 1580 nm
1430 to 1580 nm
1480 to 1580 nm
1274 to 1356 nm 1280 to 1335 nm
1430 to 1580 nm
1500 to 1580 nm
1260 to 1360 nm
1280 to 1335 nm
< 1 nm (–20 dB from center)
< 1 nm (–20 dB from center)
< 1 nm (–20 dB from center)
±50 ppm
±50 ppm
±50 ppm
±4.6
±4.6
±4.6
±2
±2
±2
3
3
3
G.957 (SDH)
GR-253 (SONET)
G.958 (SDH)
GR-253 (SONET)
G.958 (SDH)
GR-253 (SONET)
G.958 (SDH)
NRZ
NRZ
NRZ
Dual LC
Dual LC
Dual LC
SFP
SFP
SFP
(uncertainty)
OC-3/STM-1 OC-12/STM-4
OC-48/STM-16
15 km; 1310 nm 40 km; 1310 nm 40 km; 1550 nm 80 km; 1550 nm 15 km; 1310 nm 40 km; 1310 nm 40 km; 1550 nm 80 km; 1550 nm 15 km; 1310 nm
40 km; 1310 nm 40 km; 1550 nm
80 km; 1550 nm
Level Tx
–5 to 0 dBm –2 to 3 dBm –5 to 0 dBm –2 to 3 dBm –5 to 0 dBm
–2 to 3 dBm
–5 to 0 dBm
–2 to 3 dBm
–5 to 0 dBm
–2 to 3 dBm
–5 to 0 dBm
–2 to 3 dBm
Rx Level Sensitivity
–18 to 0 dBm –27 to –9 dBm –18 to 0 dBm –28 to –9 dBm –18 to 0 dBm –27 to –9 dBm –18 to 0 dBm
–28 to –9 dBm –18 to 0 dBm
–27 to –9 dBm
–18 to 0 dBm
–28 to –9 dBm
Transmit Bit Rate
Receive Bit Rate
Operational
Wavelength Range
Spectral Width
Frequency Offset
Generation
Measurement
Frequency (ppm)
Accuracy
Optical Power (dB)
Maximum Rx before
damage
a
(dB)
Jitter Compliance
Line Coding
Eye Safety
SFP/XFP transceivers comply with IEC 60825 and 21 CFR 1040.10 (except for deviations pursuant to Laser Notice No. 50, dated July 2001), for Class 1 or 1M lasers.
Connector
b
Transceiver Type