Atec Fluke-DTX Series - Manual (Page 2)

DTX CableAnalyzer ™ Series Specifications
Note: For availability of additional adapters that allow testing to other performance
standards, different cabling types, or fiber optic cabling, contact Fluke Networks.
The selected test standard determines the test parameters
and the frequency range of the tests
* The battery will not charge at temperatures outside of 0° C to 45° C (32° F to 113° F). The battery charges at a reduced rate between 40° C and 45° C (104° F and 113° F).
Cable Types
Shielded and unshielded twisted pair LAN cabling: TIA Category 3, 4, 5, 5e, and 6: 100
Ω
(STP, FTP, SSTP, and UTP) ISO/IEC Class C and D: 100
Ω and 120 Ω
ISO/IEC Class E, 100
Ω
ISO/IEC Class F, 100
Ω
Standard Link Interface Adapters
Cat 6/Class E permanent link adapters Plug type: shielded Cat 6 centered 8-pin modular plug (RJ45)
Plug life: > 5000 insertions
Tests supported: shielded and unshielded cable, TIA Cat 3, 4, 5, 5e, and 6 and ISO/IEC Class C, D
and E permanent link
Cat 6/Class E channel adapters Plug type: shielded 8-pin modular socket (RJ45)
Plug life: >10,000 insertions
Tests supported: shielded and unshielded cable, TIA Cat 3, 4, 5, 5e, and 6 and ISO/IEC Class C, D
and E channels
Test Standards
TIA Category 3 and Category 5e per TIA/EIA-568B
Category 5 (1000BASE-T) per TIA TSB-95
Category 6 per TIA/EIA-568B.2-1 (Addendum #1 to TIA/EIA-568B.2)
ISO/IEC 11801 Class C, D and E
11801-2000 Class C, D and E
11801 Class F (DTX-1800 only)
EN 50173 Class C, D ,E
50173 Class F ( DTX-1800 only)
ANSI TP-PMD
IEEE 802.3 10BASE-T, 100BASE-TX, 1000BASE-T
IEEE 802.5 (STP cabling, IBM Type 1, 150 Ω) Token Ring, 4 Mbps and 16 Mbps
General Specifications
Speed of Autotest Full 2-way Autotest of Category 6 Twisted-Pair links: 12 seconds or less
Full 2-way Autotest of ISO/IEC Class F links: 30 seconds
Supported test parameters Wire Map, Length, Propagation Delay, Delay Skew, DC Loop Resistance, Insertion Loss (Attenuation),
Return Loss (RL), RL @ Remote, NEXT, NEXT @ Remote, Attenuation-to-Crosstalk Ratio (ACR),
ACR @ Remote, ELFEXT, ELFEXT @ Remote, Power Sum ELFEXT, PSELFEXT @ Remote, Power Sum
NEXT, PSNEXT @ Remote, Power Sum ACR, PSACR @ Remote
Cable tone generator Generates tones that can be detected by a tone probe such as a Fluke Networks IntelliTone™ probe.
The tones are generated on all pairs. Frequency range of tones: 440 Hz to 831 Hz
Display 3.7 in (9.4 cm) diagonal, 240 dots wide by 320 dots high, passive color, transmissive LCD
with backlight.
Input protection Protected against continuous telco voltages and 100 mA over-current. Occasional ISDN
over-voltages will not cause damage
Case High impact plastic with shock absorbing overmold
Dimensions Main unit and Smart Remote: 8.5 in x 4.4 in x 2.4 in (21.6 cm x 11.2 cm x 6 cm), nominal
Weight 2.4 lb (1.1 kg), nominal (without adapter or module)
Power
Main unit and remote: Lithium-ion battery pack, 7.4 V, 4000 mAh
Typical battery life: 12 to 14 hours
Charge time* (with tester off): 4 hours (below 40° C)
AC adapter/charger, USA version: Linear power supply; Input 108 V ac to 132 V ac, 60 Hz ; Output 15 V dc, 1.2 A
AC adapter/charger, international version: Switching power supply; Input 90 V ac to 264 V ac, 47 to 63 Hz; Output 15 V dc, 1.2 A
(isolated output)
Memory backup power in main unit: Lithium battery
Typical life of lithium battery: 5 years
Languages supported English, French, German, Spanish, Portuguese, Italian, Japanese, and Simplified Chinese
Calibration Service center calibration period is 1 year