Atec Agilent-E4438C - Manual (Page 10)

10
SSB Phase noise [at 20 kHz offset] 1
Standard With Option UNJ
at 500 MHz (< –124 dBc/Hz) < –135 dBc/Hz, (< –138 dBc/Hz)
at 1 GHz (< –118 dBc/Hz) < –130 dBc/Hz, (< –134 dBc/Hz)
at 2 GHz (< –112 dBc/Hz) < –124 dBc/Hz, (< –128 dBc/Hz)
at 3 GHz (< –106 dBc/Hz) < –121 dBc/Hz, (< –125 dBc/Hz)
at 4 GHz (< –106 dBc/Hz) < –118 dBc/Hz, (< –122 dBc/Hz)
at 6 GHz N/A < –113 dBc/Hz, (< –117 dBc/Hz)
Residual FM 1 [CW mode, 0.3 to 3 kHz BW, CCITT, rms]
Option UNJ < N x 1 Hz (< N x 0.5 Hz) 2
Standard
Phase noise mode 1 < N x 2 Hz
Phase noise mode 2 < N x 4 Hz
Harmonics 1, 3 [output level
≤ +4 dBm, ≤ +7.5 dBm Option UNB, ≤ +4.5 dBm Option 506]
< –30 dBc above 1 GHz, (< –30 dBc 1 GHz and below)
Nonharmonics 1, 4 [ ≤ +7 dBm output level, ≤ +4 dBm Option 506]
Standard 5 With Option UNJ 6
> 3 kHz > 10 kHz
> 3 kHz
> 10kHz
offset offset
< 10 kHz
offset
offset
250 kHz to 250 MHz < –53 dBc (< –68 dBc) (< –58 dBc) < –65 dBc (< –58 dBc)
250 MHz to 500 MHz < –59 dBc (< –74 dBc) (< –81 dBc) < –80 dBc < –80 dBc
500 MHz to 1 GHz
< –53 dBc (< –68 dBc) (< –75 dBc) < –80 dBc < –80 dBc
1 to 2 GHz < –47 dBc (< –62 dBc) (< –69 dBc) < –74 dBc < –74 dBc
2 to 4 GHz < –41 dBc (< –56 dBc) (< –63 dBc) < –68 dBc < –68 dBc
4 to 6 GHz N/A N/A N/A < –62 dBc < –62 dBc
Subharmonics
Standard With Option UNJ
≤ 1 GHz
None None
>1 GHz < –40 dBc None
Jitter in µUI 1, 7, 8
Carrier SONET/SDH rms jitter Standard With option UNJ
frequency data rates bandwidth (µUI rms) (µUI rms)
155 MHz 155 MB/s 100 Hz to 1.5 MHz (359) (78)
622 MHz 622 MB/s 1 kHz to 5 MHz (158) (46)
2.488 GHz 2488 MB/s 5 kHz to 15 MHz (384) (74)
Jitter in seconds 1, 7, 8
Carrier SONET/SDH rms jitter
Standard With option UNJ
frequency data rates bandwidth
155 MHz 155 MB/s 100 Hz to 1.5 MHz (2.4 ps) (0.6 ps)
622 MHz 622 MB/s 1 kHz to 5 MHz (255 fs) (74 fs)
2.488 GHz 2488 MB/s 5 kHz to 15 MHz (155 fs) (30 fs)
Specifications for Frequency and Power Characteristics
1. Parentheses denote typical performance.
2. Refer to frequency bands on page 12 for N values.
3. Harmonic performance outside the operating range of the instrument is typical.
4. Spurs outside the operating range of the instrument are not specified. Broadband noise is not tested.
5. Specifications apply for FM deviations < 100 kHz and are not valid on FM. For non-constant amplitude formats, unspecified spur levels occur up to the
second harmonic of the baseband rate.
6. Specifications apply for CW mode only.
7. Calculated from phase noise performance in CW mode only at -2.5 dBm for standard instruments, -0.5 dBm with Option 506, and +2.5 dBm with Option UNB.
8. For other frequencies, data rates, or bandwidths, please contact your sales representative.
Spectral purity