Atec AEMC-PEL103 - Manual (Page 2)

Models PEL 102 & PEL 103
POWER & ENERGY LOGGER
PEL 100 Series
Technical Assistance (800) 343-1391 www.aemc.com
CataLog No. DEsCriPtioN
2137.51 Power & Energy Logger Model PEL 102 (no LCD, w3 MA193-10-BK sensors)
2137.52 Power & Energy Logger Model PEL 103 (with LCD, w3 MA193-10-BK sensors)
2137.61 Power & Energy Logger Model PEL 102 (no LCD, no sensors)
2137.62 Power & Energy Logger Model PEL 103 (with LCD, no sensors)
 SpEciFicATionS
gENEraL
Sampling Frequency
128 samples per cycle; 50/60Hz (16 samples/cycle 400Hz)
Data Storage Rate 1 per second
Demand Period Storage Rate User selectable (1, 2, 3, 4, 5, 6, 10, 12, 15, 20, 30 and 60 minutes)
Recorded Parameters
(Single- and Poly-Phase) V, I, W, VA, var, PF, Tan, Wh, Vah, varh, THD (V and I),
Individual harmonics (from 1 through 50 per phase); Crest Factor (CF), Cos f / DPF
Event Log Tracks and records status changes and error messages along with recorded data
Front Panel Indicator LEDs Bluetooth active, recording in progress, phase connection reversal, overload, battery charging and SD Card status
Storage Capacity 2GB SD card (included) is used for storage. SD cards (up to 2GB); SDHC cards (4 to 32GB) formatted FAT32 are supported
INPUTS Voltage 3 voltage input channels via 4mm safety banana jacks
Current 3 current input channels via custom 4 pin jacks that accept AEMC ® probes and sensors
ELECtriCaL
VOLTAGE MEASUREMENT
RANGE RESOLUTION * ACCURACY (% of Reading)
50/60Hz 42.5 to 69Hz – ±0.1Hz
Single-Phase RMS Voltages 100 to 1000rms 0.1V ±0.2% Rdg ± 0.2V
Phase-to-Phase RMS Voltages 100 to 2000Vrms 0.1 to 1V ±0.2% Rdg ± 0.4V
400Hz 340 to 460Hz – –
Single-Phase RMS Voltages 100 to 600Vrms 0.1V ±1% Rdg ± 1V
Phase-to-Phase RMS Voltages 200 to 1200Vrms 0.1 to 1V ±1% Rdg ± 1V
DC 100 to 1000V 0.1V ±1% Rdg ± 3V (typical)
PT Ratios Programmable from 50V to 65,0000V 0.01V to 0.1V –
CURRENT MEASUREMENT
Current Probe: MiniFlex
® Sensor MA193*** 200mA to 100Arms 1 to 100mA ±1% ± 50mA
20 to 400Arms 10 to 100mA ±1% ± 0.2A
100 to 2000Arms 0.1 to 1A ±1% ± 1A
500 to 10,000Arms 0.1 to 1A ±1%
CT Ratios Programmable from 1:1 to 25,000:1 (probe dependent)
POWER MEASUREMENTS
Active Power (P)*
-2 to 2GW 0.001W ±0.5% Rdg ± 0.005% Pnom
Reactive Power (Q)* -2 to 2Gvar 0.001var ±1% Rdg ± 0.01% Qnom
Apparent Power (S)* 0 to 2GVA 0.001VA ±0.5% Rdg ± 0.005% Snom
Power Factor -1 to +1 0.001 ± 0.05
Tangent φ (active/reactive power ratio) -3.2 to +3.2 0.001 ± 0.02
ENERGY MEASUREMENTS
Active Energy (EP)
0 to 4 x 10 18 1Wh ±0.5% Rdg
Reactive Energy (EQ) 0 to 4 x 10 18 1varh ±2% Rdg
Apparent Energy (ES) 0 to 4 x 10 18 1Vah ±0.5% Rdg
THD ± 655%
Individual Harmonics 1 to 50 displayed in percentage; 1 to 7 at 400Hz
External Supply 110V/250V (10%) @ 50/60Hz; 400Hz
Back-Up Power Source / Charge Time Rechargeable 8.4V NiMH battery pack / Approximately 5 hours
Battery Life Provides up to 30 minute ride through upon power loss
MECHaNiCaL
Communication Ports
USB 2.0, Ethernet (RJ45), Wireless Bluetooth Class 1 **
Dimension/Weight 10.08 x 4.92 x 1.46" (256 x 125 x 37mm) / <1kg
Case / Index of Protection Double insulated, rubber over-molded, polycarbonate UL94 V1 rated / IP54 non operating
Mounting / Security Embedded magnets on back side, keyhole slot on back side / Kensington anti-theft system
DisPLaY
Display Type for Model PEL 103
2.63 x 2.16" (67 x 55mm), four line, monochrome, backlit LCD with adjustable brightness and contrast
ENViroNMENtaL / saFEtY
Operating Temperature / Relative Humidity
32° to 122°F (0° to 50°C) / up to 85%
Storage Temperature -4° to 122°F (-20° to 50°C) with batteries; -4° to 158°F (-20° to 70°C without batteries)
Safety Rating / CE Rating Complies with IEC 61010-1:Ed3, and IEC 61010-2-030:Ed1 for 1000V CAT III / 600V CAT IV, Pollution Degree 2 / Yes
* Maximum value is current probe dependent. ** Computers with Class II Bluetooth will restrict range to 40ft. Computers without Bluetooth will require a Class I or Class II Bluetooth radio
adapter. *** Maximum current reduced by a factor of 2 for 400Hz fundamental frequency.