Atec Associated-Research_8004-05-06 - Manual (Page 4)

SPECIFICATIONS
INPUT SPECIFICATIONS
VOLTAGE 115 / 230 V selectable, ± 10% variation
FREQUENCY 50/60 Hz ± 5%
FUSE 115 VAC, 230 VAC - 6.3 A Slow-Blo 250 VAC
DIELECTRIC WITHSTAND TEST MODE
OUTPUT RATING 5 KV @ 40 mA AC
5 KV @ 20 mA DC
VOLTAGE DISPLAY Range: 0.00 - 5.00 KV Full Scale
Resolution: 0.01 KV
Accuracy:
± (2% of reading + 10 V)
HI & LO-LIMIT
AC TOTAL Range: 0.000 mA - 40.00 mA
AC REAL Range: 0.000 mA - 40.00 mA
DC Range: 0.0 - 20,000 µA
CURRENT DISPLAY
AC TOTAL Range: 0.000 mA - 40.00 mA
AC REAL Range: 0.000 mA - 40.00 mA
DC Range: 0.0 µA - 20,000 µA
RAMP HI Range: 20 mA peak maximum,
ON/OFF selectable
CHARGE LO Range: 0.000 - 350 µA or Auto Set
DC OUTPUT ≤ 4% Ripple RMS at 5 KV DC @ 20 mA,
RIPPLE Resistive Load
DISCHARGE TIME ≤ 200 ms
MAXIMUM 1 µF < 1 KV 0.75 µF < 2 KV
CAPACITIVE LOAD 0.5 µF < 3 KV 0.08 µF < 4 KV
DC MODE 0.04 µF < 5 KV
AC OUTPUT
WAVEFORM
Sine Wave, Crest Factor = 1.3 - 1.5
OUTPUT Range: 50/60 Hz, user selectable
FREQUENCY Accuracy: ± 0.1%
OUTPUT ± (1% of output + 5 V)
REGULATION from no load to full load and over input
voltage range.
DWELL TIMER Range: AC 0.4 - 999.9 sec (0 = Constant)
DC 0.3 - 999.9 sec (0 = Constant)
Accuracy: ± (0.1% + 0.05 sec)
RAMP TIMER Range: Ramp-Up: AC 0.1 - 999.9 sec
DC 0.4 - 999.9 sec
Ramp-Down: AC 0.0 - 999.9 sec
DC 0.0,1.0 - 999.9 sec
0.0 = OFF
Accuracy: ± (0.1% + 0.05 sec)
GROUND Current: DC 0.1 A ± 0.01 A, fixed
CONTINUITY Max. ground resistance: 1 Ω ± 0.1 Ω, fixed
GROUND FAULT GFI Trip Current: 450 µA max (AC or DC)
INTERRUPT HV Shut Down Speed: < 1ms
INSULATION RESISTANCE TEST MODE
VOLTAGE SETTING Range: 50 - 1000 VDC
Resolution: 1 V
Accuracy:
± (2% of setting + 2 counts)
CHARGING
CURRENT
Maximum >20 mA peak
RESISTANCE Range: 0.05 M Ω - 50000 MΩ
DISPLAY (5 Digit, Auto Ranging)
Accuracy: 50 - 499 V
0.05 M Ω - 999.9 MΩ,
± (7% of reading +2 counts)
500 - 1000 V
0.05 M Ω - 999.9 MΩ,
± (2% of reading +2 counts)
1000 M Ω - 9999 MΩ
± (5% of reading +2 counts)
10000 M Ω - 50000 MΩ,
± (15% of reading +2 counts)
RAMP HI Range: 20 mA peak maximum,
ON/OFF selectable
CHARGE LO Range: 0.000 - 3.500 µA or Auto Set
HI & LO-LIMIT Range: 0.05 M Ω - 50,000 MΩ
Accuracy: Same as Resistance
Display Accuracy
RAMP TIMER Range: Ramp-Up: 0.1 - 999.9 sec
Ramp-Down: 1.0-999.9 sec
0 = OFF
Resolution: 0.1 sec
Accuracy:
± (0.1% + 0.05 sec)
DELAY TIMER Range: 1.0 - 999.9 sec (0 = Constant)
GROUND FAULT GFI Trip Current: 450 µA max (AC or DC)
INTERRUPT HV Shut Down Speed: < 1 ms
GROUND BOND TEST MODE
OUTPUT VOLTAGE Range: 3.00 - 8.00 VAC
(Open Circuit Limit) Resolution: 0.01 V
Accuracy:
± (2% of setting + 0.03 V)
O.C. Condition
OUTPUT Range: 50/60 Hz, user selectable
FREQUENCY Accuracy: ± 0.1%
OUTPUT CURRENT Range: 1.00 - 30.00 A
Resolution: 0.01 A
Accuracy:
± (2% of setting + 0.02 A)
OUTPUT Accuracy: ± (1% of output + 0.02 A)
REGULATION Within maximum load limits, and over
input voltage range
MAXIMUM 1.00 - 9.99 A, 0 - 600 m Ω
LOADING 10.00 - 30.00A, 0 - 150 m Ω
CURRENT DISPLAY Range: 0.00 - 30.00 A
RESISTANCE
DISPLAY
Range: 0 - 600 m Ω
HI & LO LIMIT Range: 1.00 - 9.99 A, 0 - 600 m Ω
DWELL TIMER Range: 0.5 -999.9 sec (0 = Constant)
MILLIOHM OFFSET Range: 0 - 200 m Ω
CONTINUITY TEST MODE
OUTPUT CURRENT DC 0.1A ± 0.01A, fixed
RESISTANCE
DISPLAY
Range: 0.00 - 10.00 Ω,
HI & LO-LIMIT Range: 0.00 - 10.00 Ω
DWELL TIMER Range: 0.0, 0.3 - 999.9
sec (0 = Constant)
MILLIOHM OFFSET Range: 0.00 - 2.00 Ω