Atec Anritsu-MT8222A - Manual (Page 5)

5
* Excludes mismatch errors.
Excludes noise, zero set, zero drift for levels <–20 dBm.
Excludes digital modulation uncertainty between +17 and +20 dBm.
**After 30 min warm-up
T1 Analyzer, Fractional T1 and sub-channels
BER Testing: BER testing at 1.544 MB, 64, 16 and 8 kB rates
Line Coding: AMI, B8ZS
Framing Modes: D4 (Superframe), ESF (Extended Superframe)
Connection Configurations: Terminate: 100 Ω balanced, Bantam
Bridge: ≤ 1000 Ω
Monitor: Connect via 20 dB pad in DSX
Receiver Sensitivity: Terminate: +6 dB to –36 dB
Bridge: +6 dB to –36 dB
Monitor: 20 dB flat gain
Transmit Level: 0 dB, –7.5 dB, and –15 dB
Clock Sources: External Bits clock,
Internal: 1.544 MHz ± 5 ppm
Pulse Shapes: Conform to ANSI T1.403 & ITU G.703
Pattern Generation and Detection:
PRBS: 2-9, 2-11, 2-15, 2-20, 2-23 Inverted and
non-inverted, QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24,
All ones, All zeros, T1-Daly, User defined (≤ 32 bits)
Circuit Status Reports:
Carrier present, Frame ID and Sync.,
Pattern ID and Sync.
Alarm Detection: AIS (Blue Alarm), RAI (Yellow Alarm)
Error Detection: Frame Bits, Bit, BER, BPV, CRC, Error Sec
Error Insertion: Bit, BPV, Framing Bits, RAI, AIS
Loopback Modes: Self loop, CSU, NIU, User defined,
In-band or Data Link
Level Measurements: Vp-p (± 5%), can also display in dBdsx
Data Log: Continuous, up to 72 hrs
T1 Frequency Measurement: ± 5 ppm
DS0 Channel Access: Tone Generator Frequency: 100 Hz to 3000 Hz
Level: –30 to 0 dBm, with 1 dB steps
VF Measurement: Frequency: 100 Hz to 3000 Hz, ± 3 Hz
Level: –40.0 to +3.0 dBm, ± 0.2 dBm
Audio Monitor: Manually select channel 1 to 24
ITU G-821 Analysis: Errored seconds, error free seconds,
severely errored seconds, unavailable seconds,
available seconds, degraded minutes
Gated Sweep (Option 090)
The option adds gated sweep to the spectrum analyzer mode, giving the
user the capability to view pulsed or burst signals only when they are on,
or conversely look at the spectrum only when a signal is off.
Trigger Signal: External TTL input, user selectable high or low level.
Gate Delay: 0 to 65 ms typical
Gate Length: 1 µs to 65 ms typical
PIM Analyzer Specifications (Option 0419)
(requires PIM Master™)
See Product Brochure 11410-00546
LTE Specifications
Bandwidth: 10 MHz
Span: 1.4, 3, 5, 10, 15, 20 MHz
Frame Length: 2.5, 5.0, 10.0 msec
LTE RF Measurements (Option 0541)
RF Channel Power Accuracy: ± 1.0 dB typical, (RF input −50 to +10 dBm)
LTE Modulation Measurements (Option 0542)
Frequency Error: ± 10 Hz + time base error, 99% confidence level
Residual EVM (rms): 2.5 % typical (E-UTRA Test Model 3.1)
(RF Input -50 dBm to +10 dBm
LTE Over-the-Air (OTA) Measurements
(Option 0546)
Scanner: Six strongest Sync Signals
Auto Save: Yes
GPS Tagging and Logging: Yes
System
Measurement Resolution: 0.01 dB
Offset Range: ± 60 dB
Interfaces: USB A/mini-B 2.0
General Specifications
Maximum Continuous Input into Spectrum Analyzer:
10 dB attenuation, +30 dBm, ± 50 VDC
RF Input VSWR: 2.0:1 maximum, 1.5:1 typical (≥ 10 dB attenuation)
Internal Time Base Accuracy: ± 0.3 ppm
Interfaces:
Type N female RF Connector
Type N female RF Out Port and RF In Port (50 Ω)
BNC female connectors for external reference
and external trigger
Reverse BNC connector for GPS antenna
E1-2Mb/s (Receive and Transmit): RJ48 (75 Ω) connector and BNC(f) (120 Ω)
T1 (Receive and Transmit): Bantam Jack (100 Ω)
T1, T3 (Receive and Transmit): Bantam Jack (100 Ω) and BNC (75 Ω)
RF Detector: Type N(m) 50 Ω
RJ45 connector for Ethernet 10/100-Base T
2.5 mm 3-wire cellular headset connector
5-pin Mini-B USB 2.0 device connector
USB 2.0 Host connector used with PSN50
and USB Flash Drives
Maximum Input (Damage Level) into Cable and Antenna Analyzer Test Port:
Type N: +23 dBm, ± 50 VDC
Environmental: MIL-PRF-28800F Class 2
Operating: –10 ºC to 55 ºC, humidity 85%
Storage: –51 ºC to 71 ºC
Altitude: 4600 meters, operating and non-operating
Safety: Conforms to EN 61010-1 for Class 1 portable equipment
Electromagnetic Compatibility: Meets European Community requirements for
CE marking
Size: 315 x 211 x 94 mm (12.4 x 8.3 x 3.7 in.)
Weight: 4 kg (9 lbs.)