Atec Anritsu-MT8222A - Manual (Page 2)

2
Cable and Antenna Analyzer
Frequency Range: 10 MHz to 4 GHz
Frequency Range (Option 26): 10 MHz to 6 GHz
(All other specs remain the same)
Frequency Accuracy: 25 ppm
Frequency Resolution: 10 kHz
Data Points: Low, Medium, High (137/275/551)
Interference Immunity: On-Channel: +17 dBm
On-Frequency: 0 dBm (RF Out) +30 dBc RF In
1-Port Power: High: 0 dBm (typical)
2-Port Power: High: 0 dBm (typical)
Low: –35 dBm (typical)
Corrected Directivity: 42 dB (10 MHz to 6 GHz)
1-Port Accuracy:
= <0.8 + 20 log (1 ±10 –E∆/20 ) dB, typical E∆ = Directivity – Measured Return Loss
System Dynamic Range: 80 dB, 10 MHz to 3 GHz
70 dB, > 3 GHz to 5.5 GHz
65 dB, > 5.5 GHz to 6 GHz
Return Loss: Range: 0 to 60 dB
Resolution: 0.01 dB
VSWR: Range: 1 to 65
Resolution: 0.01
Cable Loss: Range: 0 to 30 dB
Resolution: 0.01 dB
1-Port Phase: Range: –180° to +180°
Resolution: 0.01°
Smith Chart: Resolution: 0.01
2-Port Gain: Range: –120 to 100 dB
Resolution: 0.01 dB
2-Port Phase: Range: –180° to +180°
Resolution: 0.01°
Distance-to-Fault: Fault Resolution (meters): (1.5 x 10 8 x vp)/∆F vp is
the propagation constant and ∆F is F2-F1 in Hz
Horizontal Range (meters): 0 to (data points-1) x Fault
Resolution to a maximum of 1500m (4921 ft.)
where datapoints = 137/275/551
Vertical Range (Return Loss): 0 to 60 dB
Vertical Range (VSWR): 1 to 65
Spectrum Analyzer
Frequency:
Frequency: 100 kHz to 7.1 GHz
Maximum Continuous Input: +30 dBm
Tuning Resolution: 1 Hz
Frequency Reference: Aging: ± 1 ppm/10 years
Accuracy: ± 0.3 ppm (25 °C ± 25 °C) + aging
Frequency Span: 10 Hz to 7.1 GHz plus 0 Hz (zero span)
Sweep Time: Minimum 100 ms, 10 µs to 600 seconds (zero span)
Sweep Trigger: Free run, Single, Video, External
Resolution Bandwidth: (–3 dB width) ± 10%, 1 Hz to 3 MHz in
1–3 sequence 8 MHz demodulation bandwidth
Video Bandwidth: (–3 dB) 1 Hz to 3 MHz in 1–3 sequence
SSB Phase Noise: –100 dBc/Hz max at 10, 20 and 30 kHz offset from
carrier –102 dBc/Hz max at 100 kHz offset from carrier
Amplitude:
Measurement Range: DANL to +30 dBm
Absolute amplitude accuracy Power Levels
≥–50 dBm, ≤35 dB input attenuation,
Preamplifier Off: 100 kHz to ≤ 10 MHz ± 1.5 dB
> 10 MHz to 4 GHz ± 1.25 dB
> 4 GHz to 7.1 GHz ± 1.75 dB
Displayed Average Noise Level (DANL in 1 Hz RBW, 0 dB attenuation,
Reference level –50 dBm, preamp on):
Frequency
Typical Max
10 MHz to 1 GHz –163 dBm –161 dBm
> 1 GHz to 2.2 GHz –160 dBm –159 dBm
> 2.2 GHz to 2.8 GHz –156 dBm –153 dBm
> 2.8 GHz to 4.0 GHz –160 dBm –159 dBm
> 4.0 GHz to 7.1 GHz –158 dBm –154 dBm
Input-Related Spurious:
(–30 dBm input, 0 dB input attenuation, Span < 1.7 GHz)
–70 dBc typical –60 dBc max*
* Exceptions:
Input Frequency Spur Level
1674 MHz –38 dBc (–48 typical)
Residual Spurious:
(Preamplifier on, RF input terminated, 0 dB input attenuation)
–100 dBm max
(Preamplifier off, RF input terminated, 0 dB input attenuation)
–90 dBm max**, 100 kHz to <3200 MHz
–84 dBm max**, 3200 to 7100 MHz
** Exceptions:
Frequency Max Spur Level (Typical)
250, 300, and 350 MHz –85 dBm
~4010 MHz –80 dBm (–90 dBm)
~5084 MHz –70 dBm (–83 dBm)
~5894 MHz –75 dBm (–87 dBm)
~7028 MHz –80 dBm (–92 dBm)
Display Range: 1 to 15 dB/div in 1 dB steps. Ten divisions displayed
Amplitude Units Log Scale Modes: dBm, dBV, dBmv, dBµV
Attenuator Range: 0 to 65 dB
Attenuator Resolution: 5 dB steps
Power Meters:
Frequency Range: 10 MHz to 7.1 GHz
Display Range: –80 dBm to +80 dBm
Measurement Range: –60 dBm to +30 dBm
Offset Range: 0 to +60 dB
Accuracy:
–40 dBm < Max ≤ +15 dBm:
10 MHz –4 GHz: ± 1.25 dB
4 GHz –7.1 GHz: ± 1.75 dB
Max > +15 dBm:
10 MHz –6.5 GHz: ± 1.75 dB
6.5 GHz –7 GHz: ± 2 dB
Max ≤ –40 dBm:
10 MHz –4 GHz: ± 1.5 dB
4 GHz –7.1 GHz: ± 1.75 dB
VSWR: 1.5:1 typical
Maximum Power: +30 dBm (1 W) without external attenuator
W-CDMA/HSDPA RF Measurements (Option 44)
Frequency Ranges :
Bands I - IX
RF Channel Power
(Temperature range 15 ºC to 35 ºC):
± 0.7 dB typical
(± 1.25 dB max)
Occupied Bandwidth Accuracy: ± 100 kHz
Residual Adjacent Channel
Leakage Ratio (ACLR)
1
(824 to 894 MHz, 1710 to 2170):
–54 dB typical at 5 MHz offset
–59 dB typical at 10 MHz offset
Leakage Ratio (ACLR)1 (2300-2700 MHz):
–54 dB typical at 5 MHz offset
–57 dB typical at 10 MHz offset
ACLR Accuracy (Single Channel Active)
(824 to 894 MHz, 1710 to 2170):
± 0.8 dB for ACLR ≥ –45 dB at 5 MHz offset
± 0.8 dB for ACLR ≥ –50 dB at 10 MHz offset
ACLR Accuracy (Single Channel Active)
(2300-2700 MHz):
± 1.0 dB for ACLR ≥ –45 dB at 5 MHz offset
± 1.0 dB for ACLR ≥ –50 dB at 10 MHz offset
Frequency Error: ± 10 Hz + Time Base Error,
99% confidence level:
± 10 Hz + Time Base Error, 99% confidence level
Specifications