ABUS FU9050 Privest Wireless Vibration Detector - Manual (Page 2)

NL1487
Einstellung via Dipswitches
Dipswitch Beschreibung
1. Schaltet die LED an oder aus
Dipswitch Position
LED
ON (Standard) leuchtet
OFF leuchtet nicht
2. Einstellung der Empfindlichkeit des
Melders
Dipswitch Position
Empfindlichkeit
ON (Default) Hoch
OFF Gering
Hinweis: Für die Feinabstimmung den
Empfindlichkeitsregler benutzen (min-max)
3. Nicht verwendet
4. Nicht verwendet
5. Nicht verwendet
6. Eistellen der Funk-Sende-Leistung
Dipswitch Position
RF Power
Transmission
ON Niedrig
OFF (Standard) Hoch
LED Anzeige
Die LED leuchtet nach jeder Detektion vorübergehend
rot. Bei geringer Batteriekapazität blinkt die LED
während der Übermittlung des Funksignals.
Grün
Zeigt einen Alarmzustand an
Rot • Schwellenwert unterschritten
• Sabotage-Anzeige
• Signalübertragung
Orange Schwellenwert überschritten
Detektionsreichweiten
Material Radius
Beton 1,5m
Steinwand 2,5m
Stahl 3,0m
Glas 3,5m
Holz 3,5m
Sperrholz 4,0m
Die angegebenen Reichweiten können je
nach Installationsort variieren. Überprüfen
Sie beim Testen des Melders seine tatsächliche
Reichweite.
Technische Daten
Frequenz 868,65 MHz
HF-Immunität 20V/m 80MHz - 1GHz
Modulation AM
Supervision
Alle 65 / 15 Minuten
Stromaufnahme ca. 10 µA standby
Batterie-
Lebensdauer CR123 3V Lithium,
ca. 5 Jahre
Betriebstemperatur 0°C – 50°C
Gewicht 65g
Abm. (HxBxT)
81 x 35 x 32 mm
Entsorgung
Geräte die so gekennzeichnet sind, dürfen nicht über
den Hausmüll entsorgt werden. Entsorgen Sie das
Produkt am Ende seiner Lebensdauer gemäß den
geltenden gesetzlichen Bestimmungen. Bitte wenden Sie
sich an Ihren Händler bzw. entsorgen Sie die Produkte
über die kommunale Sammelstelle für Elektroschrott.
Preface
Dear Customer, Thank you for purchasing this radio
vibration detector. You made the right decision in
choosing this state-of-the-art technology, which complies
with the current standards of domestic and European
regulations. The CE has been proven and all related
certifications are available from the manufacturer upon
request.
To maintain this status and to guarantee safe
operation, it is your obligation to observe these operating
instructions! In the event of questions, please contact
your local specialist dealer.
The radio vibration detector triggers an alarm for
vibrations caused typically by attempted break-ins (glass
breakage, drilling, sawing, levering). A microprocessor
analyses these vibrations. You can monitor movable
objects, windows and doors with this detector. If a
vibration above a predefined level is detected, it is
signalled to the ABUS radio alarm station. Read carefully
the notes and advice in these operating instructions! If
you do not follow these instructions, your guarantee
claim becomes invalid! We can accept no liability for the
consequences! No part of the product may be changed
or modified in any way. Selecting the installation location
The best place to install the radio vibration detector is on
objects that are not to be moved (a safe, or other
valuable objects) or penetrated (wooden doors, glass
walls, plaster walls). Use double-sided adhesive tape to
fix the detector temporarily in different locations and test
it by triggering an alarm. If it is not detected by the alarm
centre, move the detector to a new position.
Do NOT install the detector:
• At ground level
• Near large metal structures
• Near electric or gas lines
• Near electric or radio equipment
• To objects that move themselves, or upside down.
Installation
1. Open the case. Do this by inserting a screwdriver into
the gap at the bottom of the detector. Turn the
screwdriver carefully until the lid is free of the base.
2. Remove the PC board. Do this by levering it carefully
from the housing.
3. Install the detector at the selected location. Screw the
detector base-plate to the wall.
a. Hold the detector base-plate to the position where
you want to fix it.
b. Mark the positions for the screws. Use the holes
provided for this.
c. Fix the housing base-plate to the marked position.
4. Make sure that the housing base-plate lies flat on the
surface (wall removal contact closed).
5. Carefully press the PC board into the casing.
6. Remove the protective foil and insert the lithium
battery provided in the battery clip. Check for correct
battery polarity.
7. Alter the settings of the radio vibration detector by
changing the jumpers if necessary, and then close the
housing.
Learning
To use the radio vibration detector, you first have to train
it on the ABUS radio alarm centre. Proceed as follows:
1. Switch the alarm centre to learn mode. You see the
message “Scanning for signal ” on the display.
2. Press the lid and wall contact of the transmitter and
keep it pressed for at least
3 seconds to send a message to the alarm centre.
3. Check that the alarm system has recognized the
detector.
4. Switch the alarm centre back to normal operating
mode.
Setting via Dipswitches
Dipswitch Description
1. Used to enable or disable LED
Dipswitch Position
LED
ON (Default) Enabled
OFF Disabled
2. Used to determine the sensitivity of
the Shock detector
Dipswitch Position
Sensitivity
ON (Default) High
OFF Low
NOTE: For fine tuning use the sensitivity
trimmer
3. Not used
4. Not used
5. Not used
6. Used to determine the detector RF
power
Dipswitch Position
RF Power
Transmission
ON Low
OFF (Default) High
LED Indication
After each detection, the LED turns ON momentarily. On
Low Battery condition, the LED will blink during each
transmission
GREEN
Indicates an alarm condition
RED • Under-Sensitive indication
• Tamper indication
• Write message
ORANGE Over-Sensitive indication
Detection ranges
Material Radius
Concrete 1.5m
Stone wall 2.5m
Steel 3.0m
Glass 3.5m
Wood 3.5m
Plywood 4.0m
The ranges specified can vary according to the
installation location. Check for actual ranges by testing
the detector.
Technical data
Frequency 868.65 MHz
HF immunity 20V/m 80MHz– 1GHz
Modulation AM
Surveillance
Every 65 / 15 min.
Power consumption ca. 10 µA standby
Battery
lifetime CR123 3V Lithium
ca. 5 years
Ambient operating
temperature 0°C – 50°C
Weight 65g
Dimensions
(HxWxD) 81 x 35 x 32 mm
Disposal
Devices with this marking should not be put in the
household garbage. Dispose of the product at the end of
its lifetime according to the applicable regulations.
Préface
Chère Cliente, Cher Client, Nous vous remercions de
l’achat de ce détecteur radio de vibrations. Avec cet
appareil, vous avez acheté un produit qui correspond au
dernier cri de la technique. Ce produit répond aux
exigences des directives européennes et nationales en
vigueur. Sa conformité a été démontrée, les explications
et les documents correspondants étant détenus par le
fabricant.
Pour maintenir cette situation et pour garantir un
fonctionnement sans risque, il vous incombe, en tant
qu’utilisateur, de respecter ce mode d’emploi ! En cas de
questions, veuillez vous adresser à votre revendeur.
Le détecteur radio de vibrations déclenche une alarme
en cas de vibrations qui sont typiquement produites lors
de tentatives d’effraction (impact, percement, sciage,
soulèvement). Un microprocesseur analyse ces
vibrations. Vous pouvez surveiller des objets mobiles,
des fenêtres et des portes à l’aide de ce détecteur. Si
une vibration de l’intensité préréglée est détectée,
l’appareil envoie une alarme à la centrale d’alarme radio
ABUS.
Veuillez respecter les instructions et les indications
figurant dans ce mode d’emploi! Le fait de ne pas
respecter ces directives annule votre garantie! Aucune
UK
FR