Extron Electronics MLS 506SA - Manual (Page 33)

4-5 MediaLink Switchers • Serial Communication
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Audio bass adjustment (per input)
Set a specific input’s bass level. X2 * X9 < In X2 Bas= X9 Set a specific input’s bass level.
Example: 2*10< In X2 Bas=+06 Example: set input 2’s bass to +6dB.
Increment an input’s bass level. X2 *+ < In X2 Bas= X9 Increase input X9 ’s bass level.
Decrement an input’s bass level. X2 *– < In X2 Bas= X9 Decrease input X9 ’s bass level.
View a specific input’s bass level. X2 * < In X2 Bas= X9 Show input X9 ’s bass level.
Set the current input’s bass level. X2 < In X2 Bas= X9 Set the currently selected
input’s bass level.
Increment the current input’s bass. + < In X2 Bas= X9 Increase the current input’s bass .
Decrement the current input’s bass. – < In X2 Bas= X9 Decrease the current input’s bass .
View the current input’s bass level. < In X2 Bas= X9 Show the current input’s bass level.
Audio mute (overall)
Mute on (fixed & variable audio outputs) 1Z Amt1 Mute all audio outputs.
Mute off (fixed & variable audio outputs) 0Z Amt0 Unmute all audio outputs.
View the audio mute status. Z Amt X7 Show the status of audio mute.
Volume adjustment (overall)
Set the overall output volume. X10 V Vol X10 Specify the volume for the
audio output.
Example: 27V Vol013 Example: set volume to 13.
Increment the volume. +V Vol X10 Increase audio output.
Decrement the volume. -V Vol X10 Decrease audio output.
View the volume level. V Vol X10 Show the output volume.
Executive mode
Disable executive mode. 0X Exe0 Adjustments & selections can
be made from the front panel.
Enable (lock adjustments). 1X Exe1 Lock front panel adjustments;
adjust via RS-232 only. Only input
selection and volume adjustment
are available via the front panel.
View the executive mode status. X Exe X7 Show executive mode status.
Example: X Exe0
Firmware version, part number & information requests
Query firmware version number. Q Ver X11 Show the switcher’s firmware
version.
Request the part number. N N60-386-0X Show the MLS’s part #.
Request general info. I (see below) Show the MLS’s status.
Vid • Aud • Clp X1 X1 X7
Video input # X1
is selected/active.
Audio input
# X1 is
selected/active.
Audio clipping
status.
Zap (reset to default settings)
Zap all MLS settings/memories. Esc zXXX ZapXXX Reset everything (all settings
and adjustments) to the factory
default.
Zap the audio settings. zA ZapA Reset the audio settings and
adjustments to the factory
default.
Command/response table for SIS commands (continued)
Command ASCII Command Response Additional description
(host to switcher) (switcher to host)