Al8807, Pin descriptions, Absolute maximum ratings – Diodes AL8807 User Manual
Page 2: Recommended operating conditions
AL8807
Document number: DS35281 Rev. 5 - 2
2 of 20
March 2013
© Diodes Incorporated
AL8807
Pin Descriptions
Pin Name
Pin Number
Function
SOT25 MSOP-8EP
SW
1
5, 6
Switch Pin. Connect inductor/freewheeling diode here, minimizing track length at this pin to reduce EMI.
GND
2
2, 3
GND Pin
CTRL 3
4
Dimming and On/Off Control Input.
Leave floating for normal operation.
(V
CTRL
= V
REF
= 2.5V giving nominal average output current I
OUTnom
= 0.1/R
S
)
Drive to voltage below 0.4V to turn off output current
Drive with DC voltage (0.5V < V
CTRL
< 2.5V) to adjust output current from 20% to 100% of I
OUTnom
A PWM signal (low level
≤ 0.4V and high level > 2.6; transition times less than 1us) allows the output
current to be adjusted below the level set by the resistor connected to SET input pin.
SET
4
1
Set Nominal Output Current Pin. Configure the output current of the device.
V
IN
5 8
Input Supply Pin. Must be locally decoupled to GND with > 2.2µF X7R ceramic capacitor – see applications
section for more information.
EP — EP
Exposed pad/TAB connect to GND and thermal mass for enhanced thermal impedance. Should not be
used as electrical ground conduction path.
N/C — 7
No
Connection
Absolute Maximum Ratings
(@T
A
= +25°C, unless otherwise specified.)
Symbol Parameter
Ratings
Unit
ESD HBM
Human Body Model ESD Protection
2.5
kV
ESD MM
Machine Model ESD Protection
200
V
V
IN
Continuous V
IN
Pin Voltage Relative to GND
-0.3 to +40
V
V
SW
SW Voltage Relative to GND
-0.3 to +40
V
V
CTRL
CTRL Pin Input Voltage
-0.3 to +6
V
I
SW-RMS
DC or RMS Switch Current
SOT25 1.25
A
MSOP-8EP 1.6
I
SW-PK
Peak Switch Current (<10%)
2.5
A
T
J
Junction Temperature
150 °C
T
LEAD
Lead Temperature Soldering
300
°C
T
ST
Storage Temperature Range
-65 to +150
°C
Caution: Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
Semiconductor devices are ESD sensitive and may be damaged by exposure to ESD events. Suitable ESD precautions should be taken when handling
and transporting these devices.
Recommended Operating Conditions
(@T
A
= +25°C, unless otherwise specified.)
Symbol
Parameter
Min
Max
Unit
V
IN
Operating Input Voltage Relative to GND
6.0
36
V
V
CTRLH
Voltage High for PWM Dimming Relative to GND
2.6
5.5
V
V
CTRLDC
Voltage Range for 20% to 100% DC Dimming Relative to GND
0.5
2.5
V
V
CTRLL
Voltage Low for PWM Dimming Relative to GND
0
0.4
V
f
SW
Maximum Switching Frequency
1
MHz
I
SW
Continuous Switch Current
SOT25
1
A
MSOP-8EP
1.3
T
J
Junction Temperature Range
-40
+125
°C