P5nd2-sli series sata connectors sata1, Sata4, Sata3 – Asus P5ND2-SLI User Manual
Page 54: Sata2

2 - 2 8
2 - 2 8
2 - 2 8
2 - 2 8
2 - 2 8
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
4 .
4 .
4 .
4 .
4 .
N V I D I A M C P - 0 4 S o u t h B r i d g e S e r i a l A T A c o n n e c t o r s
N V I D I A M C P - 0 4 S o u t h B r i d g e S e r i a l A T A c o n n e c t o r s
N V I D I A M C P - 0 4 S o u t h B r i d g e S e r i a l A T A c o n n e c t o r s
N V I D I A M C P - 0 4 S o u t h B r i d g e S e r i a l A T A c o n n e c t o r s
N V I D I A M C P - 0 4 S o u t h B r i d g e S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ b l u e ] , S A T A 2 [ b l u e ] , S A T A 3 [ b l u e ] ,
( 7 - p i n S A T A 1 [ b l u e ] , S A T A 2 [ b l u e ] , S A T A 3 [ b l u e ] ,
( 7 - p i n S A T A 1 [ b l u e ] , S A T A 2 [ b l u e ] , S A T A 3 [ b l u e ] ,
( 7 - p i n S A T A 1 [ b l u e ] , S A T A 2 [ b l u e ] , S A T A 3 [ b l u e ] ,
( 7 - p i n S A T A 1 [ b l u e ] , S A T A 2 [ b l u e ] , S A T A 3 [ b l u e ] ,
S A T A 4 [ b l u e ] )
S A T A 4 [ b l u e ] )
S A T A 4 [ b l u e ] )
S A T A 4 [ b l u e ] )
S A T A 4 [ b l u e ] )
These connectors are for the Serial ATA signal cables for Serial ATA
3Gb/s hard disk and optical disk drives. The Serial ATA 3Gb/s is
backward compatible with Serial ATA 1.5Gb/s specification.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 0+1, RAID 5 or JBOD configuration with the Primary and
Secondary IDE drives through the onboard NVIDIA
®
MCP-04 RAID
controller. Refer to section “5.4.2 NVIDIA
®
RAID configurations” on
page 5-23 for details on how to set up Serial ATA and Parallel ATA
RAID configurations.
•
These connectors are Disabled by default. If you intend to create a
Serial ATA RAID set using these connectors, enable the F i r s t ,
F i r s t ,
F i r s t ,
F i r s t ,
F i r s t ,
S e c o n d , T h i r d o r F o u r t h
S e c o n d , T h i r d o r F o u r t h
S e c o n d , T h i r d o r F o u r t h
S e c o n d , T h i r d o r F o u r t h
S e c o n d , T h i r d o r F o u r t h S A T A
S A T A
S A T A
S A T A
S A T A M a
M a
M a
M a
M asssss t e r R A I D
t e r R A I D
t e r R A I D
t e r R A I D
t e r R A I D items in
A d v a n c e d > O n b o a r d D e v i c e s C o n f i g u r a t i o n > N V R A I D
A d v a n c e d > O n b o a r d D e v i c e s C o n f i g u r a t i o n > N V R A I D
A d v a n c e d > O n b o a r d D e v i c e s C o n f i g u r a t i o n > N V R A I D
A d v a n c e d > O n b o a r d D e v i c e s C o n f i g u r a t i o n > N V R A I D
A d v a n c e d > O n b o a r d D e v i c e s C o n f i g u r a t i o n > N V R A I D
C o n f i g u r a t i o n
C o n f i g u r a t i o n
C o n f i g u r a t i o n
C o n f i g u r a t i o n
C o n f i g u r a t i o n of the BIOS. See section “4.4.8 Onboard Devices
Configuration” on page 4-32 for details.
•
These connectors support RAID 0, RAID 1, RAID 0+1, RAID 5 and
JBOD that spans across the Parallel ATA drives.
These connectors support Native Command Queuing (NCQ), Power
Management (PM) Implementation Algorithm, Hot Swap and smart setup.
P5ND2-SLI
®
P5ND2-SLI Series SATA connectors
SATA1
GND
RSA
T
A_TXP1
RSA
T
A_TXN1
GND
RSA
T
A_RXP1
RSA
T
A_RXN1
GND
SATA4
GND
RSA
T
A_TXP4
RSA
T
A_TXN4
GND
RSA
T
A_RXP4
RSA
T
A_RXN4
GND
SATA3
GND
RSA
T
A_TXP3
RSA
T
A_TXN3
GND
RSA
T
A_RXP3
RSA
T
A_RXN3
GND
SATA2
GND
RSA
T
A_TXP2
RSA
T
A_TXN2
GND
RSA
T
A_RXP2
RSA
T
A_RXN2
GND