Asus P5ND2-SLI - Manual (Page 27)

A S U S P 5 N D 2 - S L I S e r i e s A S U S P 5 N D 2 - S L I S e r i e s A S U S P 5 N D 2 - S L I S e r i e s A S U S P 5 N D 2 - S L I S e r i e s A S U S P 5 N D 2 - S L I S e r i e s 2 - 1 2 - 1 2 - 1 2 - 1 2 - 1
Onboard LED Onboard LED Onboard LED Onboard LED Onboard LED
The motherboard comes with a standby power LED. The green LED
lights up to indicate that the system is ON, in sleep mode, or in soft-
off mode. This is a reminder that you should shut down the system
and unplug the power cable before removing or plugging in any
motherboard component. The illustration below shows the location of
the onboard LED.
The red warning LED lights up when you installed two graphics card
but did not connect the ASUS EZ Plug™. The illustration below shows
the location of the onboard LEDs.
2.1 Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any
component.
• Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
• B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e B e f o r e y o u i n s t a l l o r r e m o v e a n y c o m p o n e n t , e n s u r e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e t h a t t h e A T X p o w e r s u p p l y i s s w i t c h e d o f f o r t h e
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y .
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . Failure
to do so may cause severe damage to the motherboard, peripherals,
and/or components.
Make sure to connect the EZPlug when using two PCI Express graphics
cards and a 20-pin ATX power supply unit.
P5ND2-SLI
®
P5ND2-SLI Series Onboard LED
SB_PWR
ON
Standby
Power
OFF
Powered
Off
WARN_LED
When use 2 Graphics
but do not plug EZ-PLUG
ON OFF
When use 2 Graphics
but do plug EZ-PLUG