Asus AP1600R-E2(BI2) - Manual (Page 49)

A S U S A P 1 6 0 0 R - E 2 ( B A 2 / B I 2 ) A S U S A P 1 6 0 0 R - E 2 ( B A 2 / B I 2 ) A S U S A P 1 6 0 0 R - E 2 ( B A 2 / B I 2 ) A S U S A P 1 6 0 0 R - E 2 ( B A 2 / B I 2 ) A S U S A P 1 6 0 0 R - E 2 ( B A 2 / B I 2 ) 4 - 5 4 - 5 4 - 5 4 - 5 4 - 5
3 . 3 . 3 . 3 . 3 . U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
Set these jumpers to +5V to wake up the computer from S1 sleep
mode (CPU stopped, DRAM refreshed, system running in low power
mode) using the connected USB devices. Set to +5VSB to wake up
from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh,
power supply in reduced power mode).
• The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the
system would not power up.
• The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
2 . 2 . 2 . 2 . 2 . V G A G r a p h i c s c o n t r o l l e r s e t t i n g ( 3 - p i n V G A _ E N 1 ) V G A G r a p h i c s c o n t r o l l e r s e t t i n g ( 3 - p i n V G A _ E N 1 ) V G A G r a p h i c s c o n t r o l l e r s e t t i n g ( 3 - p i n V G A _ E N 1 ) V G A G r a p h i c s c o n t r o l l e r s e t t i n g ( 3 - p i n V G A _ E N 1 ) V G A G r a p h i c s c o n t r o l l e r s e t t i n g ( 3 - p i n V G A _ E N 1 )
These jumpers allow you to enable or disable the onboard ATI Rage XL
video graphics controller. Set to pins 1-2 to enable the video graphics
controller.
NCLV-D
NCLV-D VGA Setting
VGA_EN1
Enable
(Default) Disable
2
3 2
1
NCLV-D
NCLV-D USB device wake-up
USBPW12
(Default)
+5V +5VSB
1 2 2 3
USBPW34
(Default)
+5V +5VSB
1 2 2 3