Theatre Solution Acclaim Auditorium Seating - Manual (Page 23)

22 Specifications Acclaim Auditorium Seating
Acclaim Specifications – Theatre Seating
(This section pertains to all models of the Acclaim chair.)
PART 3 – OPTIONS
3.1 UPHOLSTERED END PANEL
A. Provide manufacturer’s standard upholstered end panel at the end of the row. The configuration of the
panel shall conform to the shape of the end standard frame, shall reside fully within the frame width and
shall present fabric surfaces to both the inside and outside of the chair. The end panel assembly shall
consist of one inside and one outside panel that are machined of 1/2” thick fiberboard and have all edges
eased to insure suitability for upholstery. The outside panel is to contain four 10-24 threaded steel inserts
to facilitate assembly to inner panel with four 10-24 x 2” flat head machine screws.
3.2 VENEER END PANEL
A. Provide manufacturer’s standard veneer end panel at the end of the row. The configuration of the panel
shall conform to the shape of the end standard frame, shall reside fully within the frame width and shall
present finished veneer surfaces to both the inside and outside of the chair. Veneer species and finish to
match hardwood armrests. The end panel assembly shall consist of one inside panel machined of 1/2”
thick birch plywood and one outside panel machined of 3/4” thick birch plywood. The outside panel is to
contain four 10-24 threaded steel inserts to facilitate assembly to the inner panel with four 10-24 x 2” flat
head machine screws.
3.3 EXTERNAL END PANEL
A. Provide manufacturer’s standard external veneer end panel at the end of the row. The configuration of the
panel shall follow the angle of the frame at the rear, and shall be vertical at the front end. The panel shall
be constructed of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical
edges. The end panel shall be stained to match the armrests.
3.4 AISLE LIGHT
A. Aisle lights shall be provided in accordance to the locations shown on the architectural drawings. The units
shall be of low voltage (24v) type and the light tube shall fit into a routed area on the underside of the
armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes and
blank cover plates shall be provided. The chair manufacturer shall also provide the necessary
transformers. All wiring and electrical connections shall be conducted at the job site and shall be the
responsibility of others.
3.5 SEAT AND ROW IDENTIFICATION TAGS
A. Provide manufacturer’s standard shape aluminum number and letter plates. Font shall be Helvetica and
the font size shall be 36pt. The number plates shall be attached to the top edge of the seat with spiral
shank nails. The row letter plates shall be attached to the top of the armrest with straight shank nails.
3.6 REMOVABLE CHAIR
A. Provide the manufacturer’s standard one, two or three chair removable units which shall include an
integrated steel sled-base that is engineered to conform to the row radii and includes two through holes per
chair for floor mounting.
3.7 FREESTANDING REMOVABLE CHAIR
A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel sled-
base that is engineered to conform to the row radii and includes extended length floor plates to allow the
chairs to remain stable with no physical attachment to the floor.
3.8 TABLET ARMS
A. Tablet arm shall be two-motion fold-away style, constructed of 1/2” medium density fiberboard, faced two
sides with matte black high-pressure laminate. The edges shall be finished with a vinyl T-molding trimmed
flush with both top and bottom surfaces.
3.9 POWER/DATA
A. Where indicated on the drawings, chair frames shall be equipped with a 115v/15amp power outlet and a
RJ-45 Category 6 data port located on the front of the frame. Wire raceways shall be provided for routing
of the wires from chair to chair. All wiring and electrical connections shall be conducted at the job site and
shall be the responsibility of others.
3.10 BOOKRACK
A. The bookrack shall be constructed of hardwoods and hardwood plywood. Bookrack shall be assembled
with tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be attached