Q-Tech QT50 - Manual (Page 5)

5
Q-TECH Corporation - 10150 W. Jefferson Boulevard, Culver City 90232 - Tel: 310-836-7900 - Fax: 310-836-2157 - www.q-tech.com
DUAL IN-LINE PACKAGES
CRYSTAL CLOCK OSCILLATORS
-5.2 to -4.5Vdc & 1.8 to 15Vdc - 0.01Hz to 200MHz
Dual In-line Packages (Revision G, August 2011 ) (ECO# 10297)
Q-TECH
CORPORATION
Environmental Specifications
Q-Tech Standard Screening/QCI (MIL-PRF55310) is available for all of our DIP packages. Q-Tech can also customize screening
and test procedures to meet your specific requirements. The DIP packages are designed and processed to exceed the following test
conditions:
Environmental Test Test Conditions
Temperature cycling MIL-STD-883, Method 1010, Cond. B
Constant acceleration MIL-STD-883, Method 2001, Cond. A, Y1
Seal: Fine and Gross Leak MIL-STD-883, Method 1014, Cond. A and C
Burn-in 160 hours, 125°C with load
Aging 30 days, 70°C, ± 0.7ppm max
Vibration sinusoidal MIL-STD-202, Method 204, Cond. D
Shock, non operating MIL-STD-202, Method 213, Cond. I
Thermal shock, non operating MIL-STD-202, Method 107, Cond. B
Ambient pressure, non operating MIL-STD-202, 105, Cond. C, 5 minutes dwell time minimum
Resistance to solder heat MIL-STD-202, Method 210, Cond. C
Moisture resistance MIL-STD-202, Method 106
Terminal strength MIL-STD-202, Method 211, Cond. C
Resistance to solvents MIL-STD-202, Method 215
Solderability MIL-STD-202, Method 208
ESD Classification MIL-STD-883, Method 3015, Class 1HBM 0 to 1,999V
Moisture Sensitivity Level J-STD-020, MSL=1
Please contact Q-Tech for higher shock requirements
45º 45º
Hybrid Case
Substrate
Die
D/A epoxy
D/A epoxy
Heat
Die
R1
D/A epoxy Substrate D/A epoxy Hybrid Case
R2 R3 R4 R5
Thermal Characteristics
JA JC CA
Die
T
T
T
C
A
J
CA
JC
(Figure 1)
(Figure 2)
The heat transfer model in a hybrid package is described in figure 1
(Based on single ASIC design) .
Heat spreading occurs when heat flows into a material layer of increased
cross-sectional area. It is adequate to assume that spreading occurs at a
45° angle.
The total thermal resistance is calculated by summing the thermal
resistances of each material in the thermal path between the device and
hybrid case.
RT = R1 + R2 + R3 + R4 + R5
The total thermal resistance RT (see figure 2) between the heat source
(die) to the hybrid case is the Theta Junction to Case (Theta JC) in°C/W.
• Theta junction to case (Theta JC) for this product is 24°C/W.
• Theta case to ambient (Theta CA) for this part is 105°C/W.
• Theta Junction to ambient (Theta JA) is 130°C/W.
Maximum power dissipation PD for this package at 25°C is:
• PD(max) = (TJ (max) – TA)/Theta JA
• With TJ = 175°C (Maximum junction temperature of die)
• PD(max) = (175 – 25)/130 = 1.15W