Q-Tech QTV726 Sine Wave - Manual (Page 7)

QTV724, QTV725 and QVT726
Sine-Wave 32 Flat Pack
REV.
Q-TECH Corporation
10150 W. Jefferson Blvd.
Culver City, CA 90232
SIZE
A
CAGE NO.
51774
Sheet 7 of 7 1.0
1
16 17
32
1.015 MAX.
30X .050 ± .005
NON-ACCUMULATIVE
32X .015 ± .003
2X .750
.325 ± .025
2 PLACES
32X .010 ± .002
.200 MAX.
32X .072 ± .007
ESD SYMBOL
FOR PIN NO. 1
D/C S/N
Q-TECH USA
PART NUMBER
FREQUENCY
1.015 MAX.
TYP. REF.
4X R. 025 MAX.
2X .125 REF.
▀
PART NUMBER GENERATION
SERIES
Output type and
supply voltage
TEMPERATURE RANGE (°C)/ Max. Overall
Stability/ Min. Frequency Pulling
and Voltage Control Range
Level
FREQUENCY
(MHz)
4: SINE WAVE +3dBm …..5V N: 0.....+50°C
±25 ppm ±50 ppm Vc=0.5..6.0V
E: Eng. Model 10……225
5: SINE WAVE +7dBm ….12V P: 0.....+70°C
±35 ppm
±70 ppm Vc=0.5..6.0V M: Flight Model
6: SINE WAVE 7dBm …..15V Q: 20…+70°C
±40 ppm ±80 ppm Vc=0.5..6.0V
R: 40…+85°C
±45 ppm ±90 ppm Vc=0.5..6.0V
U: -55.+125°C
±65 ppm ±130 ppm Vc=0.5..6.0V
QTV72:
24 Pin
Flat Pack
(See note 1 below)
1. Variations from standard specification are available, please contact factory.
QTV725URM-100.000000 would be a Flight Model version HF VCXO, 32 pin SMD flat pack, sine-wave 12 volts, overall
frequency stability (Overall Frequency stability (including operating temperature, ±5% Load Change, ±5% Supply
Voltage change, 10 year aging, and radiation) ±45 ppm over -40…+85°C, @ 50 MHz with frequency pulling range from
minimum of 90 ppm below center frequency at 0.5V to a minimum of 90 ppm above center frequency at 6V.
QTV725URE-100.000000
would be a Engineering Model version HF VCXO, 32 pin SMD flat pack, sine-wave 12 volts,
overall frequency stability (Overall Frequency stability (including operating temperature, ±5% Load Change, ±5% Supply
Voltage change, 10 year aging, and radiation) ±45 ppm over -40…+85°C, @ 50 MHz with frequency pulling range from
minimum of 90 ppm below center frequency at 0.5V to a minimum of 90 ppm above center frequency at 6V.
FIGURE 1 INTERFACE CONTROL DRAWING
32 pin Flat-Pack
PIN NO. DESIGNATION
1 - 3 NC
4 Voltage Control
5 Ground/Case
6 - 10 NC
11 Supply Voltage
12 RF Output
13 Supply Voltage
14 - 32 NC
NOTES:
•
Dimensions are in inches.
•
Lead numbers are for reference only and
are not marked on the unit.
•
A triangle symbol is marked on the corner
of the package to indicate Pin 1
•
All pins with NC function may not be
connected as external tie or connections
(Pins may be connected internally).