B&B Electronics EIRP610-2SFP-T - Datasheet User Manual
Eirp610-2sfp-t

www
.
bb
-
elec
.
com
|
orderIng InFormAtIon
Model nuMBer descriPtion
EIRP610-2SFP-T
Industrial Gigabit Switch (8 CU, 2 CU/SFP)
Power Over Ethernet Sourcing
managed Industrial ethernet switch
2 gB rJ-45/sFP Ports, 8 Poe Ports
EIRP610-2SFP-T
The EIRP610-2SFP-T is a 10 Port Managed Industrial Gigabit Ethernet
Switch. In addition to 8 PoE copper RJ-45 ports, it has 2 RJ-45/SFP
Combo ports to accommodate Gigabit Ethernet.
small Form-factor Pluggable (sFP) Port: The SFP Ports provide
flexibility when planning a network. Modules are available in multiple
fiber formats. If an SFP module is not inserted, the associated combo port
can be used with standard RJ-45 copper.
high-speed transmissions: The switch includes a switch controller
that automatically senses transmission speed (10/100/1000 Mbps on two
RJ45/SFP combo ports; 10/100 on eight PoE RJ45 copper ports).
The RJ-45 interface also auto-detects MDI or MDI-X, eliminating the
requirement for a crossover cable. Each port is buffered and supports
store-and-forward protocol.
dual Power input: To reduce the risk of power failure, the switch has
two 48 VDC power inputs. If the power fails, the switch will automatically
use the secondary power input. Also, if the power goes out the
corresponding P1 or P2 LED will go out and the Fault LED will light. The
contacts for the alarm output will also open.
Flexible Mounting: IP30 metal enclosure - DIN or Panel mounted.
Managed: Powerful management functions including SNMP, LACP, VLAN,
Port Trunking, Port Mirroring, Redundant Ring Technology, and Spanning
Tree/Rapid Spanning Tree Protocol.
Power over ethernet (Poe): The eight 10/100 ports are classified as
power sourcing equipment (PSE). These ports can be used to power
IEEE 802.3af compliant powered devices (PD), eliminating the need for a
separate power supply for each device.
wide operating temperature: With an operating temperature of -40
to 75°C (-40 to 167°F), this switch is suitable for use in harsh industrial
environments.
easy troubleshooting: There are two LED indicators for each port that
display the link status and transmission speed. Three LED indicators for
power (P1, P2 and Fault) show power status. FWD LEDs on each PoE port
indicate when a powered device is connected. These indicators allow
you to quickly diagnose and correct problems and ensure your network
remains reliable.
• Eight 10/100 BaseT 802.3af end point PoE injector ports
• Two RJ-45/SFP combo slots for Gigabit Ethernet
• Redundant ring technology for fast recovery
• Wide operating temperature
• DIN Rail or Panel Mount
• NEMA TS2
Product FeAtures
AccessorIes
SDR-240-48 - DIN-Rail Power Supply, 10A, 240W, 48V
C5UMB3FBL - 3 ft. - Blue - Category 5e UTP Patch Cord
DFMM-LCLC-1M - Multi-Mode Duplex Fiber Cable, LC To LC, 1 Meter
DFSM-LCLC-1M - Single-Mode Duplex Fiber Cable, LC To LC, 1 Meter
SFP-1000SX-M-550M-T - SFP Module, 1000Base-SX, Multi-mode 550m, LC
Connector (-40 to 85°C)
SFP-100FX-M-2KM-T - SFP Module, 100Base-FX, Multi-mode 2km, LC Connector
(-40 to 85°C)
SFP-1000LX-S-10KM-T - SFP Module, 1000Base-LX, Single-mode 10km, LC
Connector (-40 to 85°C)
SFP-1000LX-S-20KM-T - SFP Module, 1000Base-LX, Single-mode 20km, LC
Connector (-40 to 85°C)
SFP-100FX-S-30KM-T - SFP Module, 100Base-FX, Single-mode 30km, LC
Connector (-40 to 85°C)
mechAnIcAl dIAgrAm
6.2 cm
2.44 in
8.4 cm
3.31 in
6.2 cm
2.44 in
13.1 cm
5.16 in
EIRP610-2SFP-T_3713ds