B&B Electronics 850-18510 - Datasheet - Manual

800-624-1070 www.imcnetworks.com Making Your Net
Work
Better — Since 1988
M
edia
C
onversion
Features and Benefits
Meets a variety of installation
requirements
• Available for multi-mode or single-mode
fiber
• Double fiber capacity with single-strand
fiber versions
• ST, SC or SFP (LC) connector
• iMcV-Gigabit TX/SFP is compatible with
IMC Networks’ SFPs and all standard
MSA compliant SFP transceivers
Easy to configure and manage with
GUI-based iView
• Monitor links and receive vital traffic and
health information and notification should
problems occur
Maximizes network uptime
• Modular, hot-swappable architecture reduces
operational costs associated with product
installation, upgrades and maintenance
Eases Troubleshooting
• LinkLoss and FiberAlert features, plus SNMP
management and LEDs assist in diagnosing
problems on fiber optic networks
• Features Link Fault Pass-Through (LFPT),
a troubleshooting feature that monitors the
copper and fiber ports of the unit;
if a port loses LINK, the unit disables
the transmitting signal on the other port
(Pass-Through) and notifies the user via
LED (available on iMcV-LIM [100],
iMcV-Gigabit and IE-iMcV-Gigabit)
• Supports Config Control, a feature that
retains the latest configuration on a module
regardless of how the initial configuration
was setup; whether by DIP Switch or SNMP
Management Module (available on iMcV-LIM
[100] & iMcV-Gigabit)
The iMcV series includes:
• iMcV-PIM converts copper to fiber at
a data rate of 10 Mbps
• iMcV-LIM converts copper to fiber at
a data rate of 100 Mbps
• iMcV-LIM 10/100 converts 10 Mbps
copper to 10 Mbps fiber OR converts
100 Mbps copper to 100 Mbps fiber
• iMcV-Gigabit converts copper to fiber
at a data rate of 1Gbps
• IE-iMcV-Gigabit TX/SFP converts copper
to fiber (via SFP transceiver) at a data rate
of 1 Gbps
10 Mbps, 100 Mbps, 10/100 Auto Negotiating and Standard and
Extended Temperature (IE) 1000 Mbps Ethernet SNMP-Manageable Media Converters
iMcV Series Modules
Monitor and control all connections from a central site with iMcV Series
SNMP-manageable media conversion modules.
Application Example
These iMcV series modules make the critical connection
between twisted pair and fiber optics. Most are also
available in a single-strand fiber version which allows two
wavelengths to share one fiber strand — Full-Duplex data
travels on different wavelengths (1310 nm and 1550 nm,
for example)— doubling the capacity of fiber. Deploy
single-strand fiber products in pairs, or connect two
compatible IMC Networks single-strand fiber products.
Satisfying today’s networking needs while preparing for tomorrow’s
requirements in cabling bandwidth, distance and security can
make designing and installing the physical layer of networks a
daunting task. The decreasing cost of fiber optic cabling and
switching equipment makes all-optical LANs the obvious choice
when future-proofing a network. Replacing legacy equipment and
the wiring infrastructure is a costly choice that could produce too
much network downtime. Managed media conversion allows the
implementation of new technologies on an existing network and
the monitoring of all connections to keep networks up-to-date and
running in peak condition.
Easily configure and manage converters with the GUI-based iView².
As an SNMP management application, iView² gives network
managers the ability to monitor and control IMC Networks'
products. iView² runs standalone on Windows NT/XP/2000, as
a standalone Java Application for other operating systems, as a
snap-in module for HP OpenView, as a Web Server running under
IIS or as a Java Web Servlet. For assistance in selecting the right
version of iView² for your operating system, visit our web site at:
http://www.imcnetworks.com/Products/iView2.cfm
RoHS
Compliant
* SFPs sold separately