Rainbow Electronics MAX1427 - Manual (Page 2)

MAX1427
15-Bit, 80Msps ADC with -79.3dBFS
Noise Floor for Baseband Applications
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(AV CC = 5V, DV CC = DRV CC = 2.5V, GND = 0, INP and INN driven differentially with -1dBFS, CLKP and CLKN driven differentially
with a 2V P-P sinusoidal input signal, C L = 5pF at digital outputs, f CLK = 80MHz, T A = T MIN to T MAX , unless otherwise noted. Typical
values are at T A = +25°C, unless otherwise noted. ≥+25°C guaranteed by production test, <+25°C guaranteed by design and char-
acterization.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
AV CC , DV CC , DRV CC to GND.................................. -0.3V to +6V
INP, INN, CLKP, CLKN, CM to GND........-0.3V to (AV CC + 0.3V)
D0–D14, DAV, DOR to GND..................-0.3V to (DRV CC + 0.3V)
Continuous Power Dissipation (T A = +70°C)
56-Pin Thin QFN (derate 47.6mW/°C above +70°C)................
3809.5mW
Operating Temperature Range ...........................-40°C to +85°C
Thermal Resistance
θJ A ...................................................21°C/W
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC ACCURACY
Resolution 15 Bits
Integral Nonlinearity INL f IN = 15MHz ±1.5 LSB
Differential Nonlinearity DNL f IN = 15MHz, no missing codes guaranteed ±0.4 LSB
Offset Error -12 +12 mV
Gain Error -4 +4 %FS
ANALOG INPUT (INP, INN)
D i ffer enti al Inp ut V ol tag e Rang e V DIFF Fully differential inputs drive, V DIFF = V INP - V INN 2.56 V P-P
Common-Mode Input Voltage V CM Self-biased 3.38 V
Differential Input Resistance R IN
1
±15%
k
Ω
Differential Input Capacitance C IN 1 pF
Full-Power Analog Bandwidth FPBW -1dB -1dB rolloff for a full-scale input 200 MHz
CONVERSION RATE
Maximum Clock Frequency f CLK 80 MHz
Minimum Clock Frequency f CLK 20 MHz
Aperture Jitter t
AJ
0.21 ps
RMS
CLOCK INPUT (CLKP, CLKN)
Full-Scale Differential Input
Voltage
V DIFFCLK
0.5 to
3.0
V
Common-Mode Input Voltage V CM Self-biased 2.4 V
Differential Input Resistance R INCLK
2
±15%
k
Ω
Differential Input Capacitance C INCLK 1 pF
DYNAMIC CHARACTERISTICS
Thermal + Quantization
Noise Floor
NF Analog input <-35dBFS -79.3 dBFS
f IN = 5MHz at -1dBFS 76.5
f IN = 15MHz at -1dBFS 73.5 76.1 Signal-to-Noise Ratio (Note 1) SNR
f IN = 35MHz at -1dBFS 75.6
dB