C&H Technology 128 SAL-RPM - Manual (Page 10)

Document Number: 28354 For technical questions, contact: [email protected] www.vishay.com
Revision: 31-Aug-09 161
128 SAL-RPM
Aluminum Capacitors Solid Al,
Radial Pearl Miniature
Vishay BCcomponents
Table 3
TEST PROCEDURES AND REQUIREMENTS
TEST PROCEDURE
(quick reference)
REQUIREMENTS
NAME OF TEST REFERENCE
Endurance IEC 60384-4/
EN130300
subclause 4.13 T
amb
= 125 °C;
U
R
= 6.3 V to 25 V with U
R
applied;
U
R
= 40 V with U
C
applied;
10 000 hours
Δ
C/C: ± 10 %
tan δ ≤ 1.2 x spec. limit
Z ≤ 1.2 x spec. limit
I
L5
≤ spec. limit
Useful life CECC 30302
subclause 1.8.1 T
amb
= 125
°C;
I
R
applied and:
U
R
= 6.3 V to 25 V with U
R
applied;
U
R
= 40 V with U
C
applied;
20 000 hours
Δ
C/C: ± 15 %
tan δ ≤ 1.5 x spec. limit
Z ≤ 1.5 x spec. limit
I
L5
≤ spec. limit
no short or open circuit,
no visible damage
total failure percentage:
< 1%
Shelf life (storage at
high temperature) IEC 60384-4/
EN130300
subclause 4.17 T
amb
= 125 °C; no voltage applied;
500 hours
Δ
C/C: ± 10 %
tan δ ≤ 1.2 x spec. limit
I
L5
≤ spec. limit
Charge and discharge IEC 60384-4-2
subclause 9.21 10 6 cycles without series resistance:
0.5 s to U
R
;
0.5 s to ground
Δ
C/C: ± 5 %
no short or open circuit,
no visible damage
Solvent resistance IEC 60068-2-45,
test XA
IEC 60653 immersion: 5 min ± 0.5 min with or without
ultrasonic at 55 °C ± 5 °C
solvents: demineralized water and/or calgonite
solution (20 g/l)
visual appearance not affected
Extended vibration IEC 60068-2-6
test Fc 10 Hz to 2000 Hz; 1.5 mm or 20 g;
1 octave/min; 3 directions;
1 sweep per direction; no voltage applied no intermittent contacts
no breakdown
no open circuiting
no mechanical damage
Δ
C/C: ± 5 %
tan δ ≤ 1.2 x spec. limit
Z
≤ 1.2 x spec. limit
I
L5
≤ 1.5 x spec. limit
Shock IEC 60068-2-27
test Ea half-sine or sawtooth pulse shape; 50 g; 11 ms;
3 successive shocks in each direction of
3 mutually perpendicular axes;
no voltage applied no intermittent contacts
no breakdown
no open circuiting
no mechanical damage
Δ
C/C: ± 5 %
tan δ ≤ 1.2 x spec. limit
Z ≤ 1.2 x spec. limit
I
L5
≤ 1.5 x spec. limit
Passive flammability IEC 60695-2-2 capacitor mounted to a vertical printed-circuit
board,
one flame on capacitor body;
T
amb
= 20 °C to 25 °C;
test duration = 20 s
after removing the test flame from
the capacitor, the capacitor must not
continue to burn for more than 15 s;
no burning particles must drop from
the sample