Altronix HubWay LD8CDS Installation Instructions - Manual (Page 2)

- 2 - HubWayLD Active Unit
Overview:
Altronix HubWayLD8CDS Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485
data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a space saving 1U EIA
19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 3000 ft. max. per
channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayDv
or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC, PTC
protected outputs with surge suppression. An optional HubSat4D Passive UTP Transceiver Hub with Integral Camera
Power unit can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher
structured cable back to the HubWayLD8CDS. In addition, the HubSat4D units provide power to these cameras locally to
eliminate the possibility of voltage drop associated with long cable runs.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.
Installation Instructions:
1. Attach mounting brackets to the HubWayLD unit for rack or wall mount installation (Figs. 6-7, pg. 8).
Affix rubber pads to the HubWayLD unit for shelf installation (Fig. 8, pg. 8).
2. Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least
3” from any video monitors).
3. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7).
4. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWayLD8CDS unit (Fig. 1f, pg. 4).
Insert the plug end of the line cord into a grounded AC receptacle.
5. Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1a, pg. 4).
6. Connect the BNC video outputs for HubWayLD8CDS Channels 1-8 to the corresponding video inputs on
the head end equipment (DVR) (Fig. 1d, pg. 4).
Agency Listings:
• UL Listed for Commercial CCTV Equipment (UL 2044).
CUL Listed - CSA Standard C22.2 No.1-04, Audio,
Video and Similar Equipment.
Input:
• 115VAC 60Hz, 1.5 amp.
Video:
• Eight (8) channels of video over twisted pair
up to a distance of 3000 ft.
• Eight (8) 75 ohm video outputs.
Data:
• RS422/RS485 data inputs.
Power:
• Individually selectable 24VAC or 28VAC power outputs
with OFF position.
• Unit provides up to 1 amp max. per channel not to
exceed a total of 5 amp (150VA) maximum current.
• PTCs are rated @ 1 amp per channel.
• Surge suppression.
Visual Indicators:
• AC input power indicator.
• Eight (8) power LED indicators.
Features:
• Picture and Gain control.
• Illuminated master power disconnect circuit breaker
with manual reset.
• IEC 320 - 3-wire grounded line cord (detachable).
• Unit can be rack, wall or shelf mounted.
• 1U rack mount chassis for use in standard EIA 19” rack.
Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
• Optional HubSat4D allows transmission of up to
four (4) video signals over a single CAT-5 or higher
structured cable.
HubWayLD8CDS Specifications:
Additional Models:
HubWayLD82CDS
• HubWayLD8CDS with eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners for 24VAC Cameras.
HubWayLD83CDS
• HubWayLD8CDS with eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners for 12VDC Cameras.