York EVAPORATOR BLOWERS K2EU060 - Manual (Page 18)

036-21300-002-A-0905
18 Unitary Products Group
ACCESSORIES
• ELECTRIC HEATER - Add 14-1/4” to unit height when using 10,
16, 26, or 36 KW heater
• SUPPLY AIR PLENUM - Add 27” to unit height when used.
• BASE - Add 24” to unit height when used.
• HOT WATER OR STEAM COIL - Add 6” to unit depth when used.
FIGURE 3 - UNIT DIMENSIONS KEU180
2 7 - 5 / 8
2 - 3 / 8
2 - 3 / 1 6
5 6 - 3 / 8
1
2 - 3 / 1 6
3 1 - 5 / 8
3 - 1 / 8
6 2 - 5 / 8
1 - 1 / 4 " K N O C K O U T
F O R 7 / 8 " O D D R A I N
C O N N E C T I O N *
( M u s t b e t r a p p e d )
F I L T E R A C C E S S P A N E L
F i l t e r s c a n b e r e m o v e d
t h r o u g h e i t h e r s i d e o f
t h e u n i t .
1 - 1 / 4 " K N O C K O U T F O R
5 / 8 " O D L I Q U I D C O N N E C T I O N *
C O I L
S E C T .
6 - 1 / 4 3 - 1 / 8
3 - 1 / 8
1 9
1 0
2 - 1 / 8
2 - 5 / 8 "
K N O C K -
O U T F O R
1 - 5 / 8 " O D
S U C T I O N
C O N N . *
3 2 - 3 / 8
1 8 - 7 / 8
6
5 - 1 / 2
5 - 7 / 8
B L O W E R
S E C T I O N
7 - 1 / 4
1 6 - 1 / 2
7 / 8
1 9 - 3 / 8
2 1 - 7 / 8
6 0 - 3 / 4
B L O W E R M O T O R A N D D R I V E A C C E S S P A N E L
( A l w a y s o n t h e w i r i n g c o n n e c t i o n s i d e o f u n i t )
L o c a t e d o n o p p o s i t e s i d e O N L Y w h e n t h e b l o w e r
s e c t i o n h a s b e e n r o t a t e d 1 8 0 f r o m p o s i t i o n s h o w n .
1 - 2 3 / 3 2 " K N O C K O U T
R e m o v e o n l y w h e n E l e c t r i c
H e a t A c c e s s o r y i s u s e d .
7 / 8 " K N O C K O U T F O R P O W E R W I R I N G
D o n o t r e m o v e t h i s k n o c k o u t w h e n t h e u n i t i s e q u i p p e d w i t h a n E l e c t r i c
H e a t A c c e s s o r y . R e f e r t o d e t a i l o f t h e H e a t e r A c c e s s o r y f o r p o w e r
w i r i n g a c c e s s o p e n i n g
7 / 8 " K N O C K O U T F O R
C O N T R O L W I R I N G
A L T E R N A T E
2 - 5 / 8 " K N O C K O U T *
* R e f e r t o I N S T A L L I N G R E F R I G E R A N T M A I N S i n i n s t a l l a t i o n i n s t r u c t i o n
w h e n p i p i n g t h r o u g h t h e o p p o s i t e s i d e o f t h e u n i t .
A I R
O U T
A I R
I N
TABLE 20: UNIT CLEARANCES KEU180
MINIMUM CLEARANCES 180
Side Air with RETURN AIR opening 24”
Side with SUPPLY AIR opening 1 24”
Side with PIPING CONNECTIONS 2 61”
Side opposite PIPING CONNECTIONS 3 26”
Bottom 4 -
1. Overall dimension of the unit will vary if an electric
heater, a supply air plenum or a base is used.
2. This dimension is required for removal of the DX coil.
Only 26” is required for normal servicing.
3. If the coil has to be removed, this dimension is required
to loosen screws that secure the coil to the unit frame.
This dimension will also be required for blower motor
access if the piping connections are made on the oppo-
site side of the unit.
4. Allow enough clearance to trap the condensate drain
lines.
All dimensions are in inches. They are
subject to change without notice. Certi-
fied dimensions will be provided upon
request.