Viking M0706VR - Manual (Page 11)

21 20
Setting the Bake Hours Program
The Bake Hours program is used for controlled timing of baked or roasted
foods. At the end of the timed cycle, the oven automatically turns off.
Setting the Automatic Start Time Bake Program
The Bake Hours program is used for controlled timing of baked or roasted
foods. At the end of the timed cycle, the oven automatically turns off.
To Set The Bake Hours Program
1. Turn the “manual” knob to “upper timed” or “lower timed” position,
depending upon the oven mode and oven being used.
2. Set the Oven Function Selector to the BAKE, CONVECTION BAKE, or
TRUCONVEC position, depending upon the type of baking being used.
3. Set the temperature control knob to the desired temperature and allow
for preheating.
4. Press and release the bake hours button. The timer will display :00 with
the words SET and COOK in the upper right corner of the digital
display.
5. Turn the “Set” knob until the desired baking time is displayed in hours
and minutes. The cook time/remaining time and the word COOK will
be displayed.
The word COOK will flash and the tone will sound three times when the
time is completed; oven will turn off. The tone will sound twice every ten
seconds after completion until timer function is cleared.
To set the Automatic Time Bake Program
1. Set the start time:
A) For Single Ovens – Program the start time by pressing the “start
time” button and turning the “Set” knob until the desired start time is
displayed. This is the time of day you want the food to begin cooking.
B) For Double Ovens – Press the “start time” button once to set the
starting time for the upper oven (
UPPER OVEN will show on the
display). Press the “start time” button twice to set the starting time for
the lower oven (
LOWER OVEN will show on the display). Then
program the start time by turning the “Set” knob until the desired start
time is displayed. This is the time of day you want the food to
begin cooking.
Clocks and Timers
(Analog Clock)
Product Controls
Clocks and Timers
(Analog Clock)
2. Set the desired baking time:
Once the start time is set, the display will switch to :00 and
the words
SET, COOK and TIME will appear on the right side of the
display. You will now enter the desired baking time.
Turn the “Set” knob until the desired baking time is displayed in hours
and minutes. Once the desired bake time is set, the word
SET will
disappear and the word DELAY will appear in the display indicating that
the Bake Hours program has been set.
NOTE: For Double Ovens, the word
DELAY will show with either UPPER
OVEN or LOWER OVEN depending on which oven has been selected.
3. Set the Oven Function selector to the desired function – BAKE,
CONVECTION BAKE, OR TRUCONVEC, etc.
4. Set the temperature control knob to the desired baking
temperature.
5. The automatic time bake program is now set!
NOTE: The display will continue to show the amount of bake time that was
programmed (this will remain until the programmed start time is reached).
You can return the display to clock mode by pressing the “probe/temp”
button – Notice that a small clock will be displayed in the upper right
corner to indicate that a program is in progress. Switch back to the timer
mode by pressing the
“bake hours” button.
6. When the specified time is reached, the oven will automatically turn on.
It will bake for the programmed amount of time at the selected
temperature.
NOTE: At one minute from the end of the specified bake program, the
oven timer will beep once. At the end of the specified bake program, the
oven will automatically turn off and the timer will sound a series of three
beeps. This will continue until the “start time” button is pressed. The
display will then return to displaying the time.
NOTE: Setting the remaining duration time to :00 will cancel the Automatic
Bake program.
Product Controls