Toshiba MW26H82 - Manual (Page 53)

53
Recor
ding (VCR)
Timer recording
Timer recording can be programmed on-screen with the remote control.
The built-in timer allows automatic unattended recording of up to 8
programs within 1 month.
ENTER
TIMER REC
MENU
TV/VCR
/ / /
Timer recording
Preparation:
• Press TV/VCR to select the TV/VCR mode.
• Load a cassette tape with the erase prevention tab intact.
• Check the time and date are correct
21 .
Example:
Program a timer recording for 23rd day, channel 125
(Cable TV), 7:00 - 9:30 PM (Tape speed : SLP).
Press MENU, then press or to select
VCR SETUP menu.
Press or to select one of the program line,
then press ENTER.
Press or to select the date, then press .
Press or to select “TIMER REC SET”, then
press .
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or crimi-
nal liability.
Notes:
• Press
to move cursor back-
ward for correction.
• To record from external
source set the channel to
“VIDEO1” or “VIDEO2”.
Set the start time, end time, channel and tape
speed as in step 4.
Then press ENTER.
To set the timer for another program, repeat
steps 3 to 5 to set another program.
Press TIMER REC. The TIMER REC indicator
will light. The Timer is programed, when the
programed time is reached, the recording is
automatically started.
To cancel timer recording, press the
button again and TIMER REC
indicator will go out.
TIMER REC
1
3
4
5
6
7
2
Notes:
• The VCR section cannot be used while the TIMER REC in-
dicator is lit. If you want to use the VCR operation, press
TIMER REC to deactivate the timer.
• When the clock is not set, you cannot select “TIMER REC”.
In this case, set the clock 21 .
• After a power failure or disconnection of the power plug,all
programmed recording setting and time display will be lost
upon resumption of power. In this case, reset the clock
21
and reprogram any timer recordings.
• If you want to correct the digits while setting, press or
until the item you want to correct, then press or to
correct the desired setting.
• If programming is performed without a tape in the unit, or
with a tape without an erase prevention tab, the Timer Re-
cording is not possible. If a tape without an erase prevention
tab is in the unit, the tape will be ejected.
V C R S E T U P
T I M E R R E C S E T
A U T O R E P E AT
: S E L E C T : A D J U S T
R E T U R N : E N D
O F F
V C R S E T U P
T I M E R R E C S E T
A U T O R E P E AT
: S E L E C T : A D J U S T
R E T U R N : E N D
O F F
TIMER REC SET
:SELECT
RETURN:END ENTER:SET
DATE
VCR SETUP
CH SPEED START END
TIMER REC SET
DATE
START
END
CH
SPEED
:SELECT :ADJUST
RETURN:END ENTER:SET
23 (THU)
12:00AM
12
SP
TIMER REC SET
DATE
START
END
CH
SPEED
:SELECT :ADJUST
RETURN:END ENTER:SET
23 (THU)
7:00PM
9:30PM
125
SLP
:SELECT
RETURN:END ENTER:SET
23 (THU) 125 SLP 7 00PM 9 30PM
VCR SETUP
TIMER REC SET
DATE CH SPEED START END
5V90101A [E]p52-56 8/4/06, 5:47 PM 53