TDK J Series JBW - Manual (Page 4)

(4/30)
004-02 / 20070523 / ea122_jbw.fm
• All specifications are subject to change without notice.
JBW15W Type
SPECIFICATIONS AND STANDARDS
∗ Current rating(maximum output current) is determined for –10 to +50°C. Derating is required when used outside this temperature range.
• Optional input, output cable kits are available at a separate price.
Part No. JBW05-3R0 JBW12-1R3 JBW15-1R0 JAW24-0R7
Rated output voltage and current ∗ 5V • 3A 12V • 1.3A 15V • 1.0A 24V • 0.7A
Maximum output power W 15 15.6 15 16.8
Input conditions
Input voltage Eac/Edc
V 85 to 265[Rating: 100 to 240]/110 to 370
Input frequency Hz 47 to 440[Rating: 50 to 60](Single phase)
Input current A 0.36typ./0.43max.[AC.100V]0.2typ./0.24max.[AC.240V]
Fuse rating A 2[AC.250V, built-in]
Surge current A 15typ./19.5max.[AC.100V]30typ./41max.[AC.240V] 1st surge current, cold start, reset after 1s minimum.
Leakage current mA 0.2typ./0.75max.[AC.100V, 60Hz]0.3typ./0.75max.[AC.240V, 60Hz]
Power factor 0.6typ./0.45typ.[AC.100/240V]
Efficiency
% 72typ.[AC.100V] 76typ.[AC.100V] 76typ.[AC.100V] 78typ.[AC.100V]
% 72typ.[AC.240V] 74typ.[AC.240V] 74typ.[AC.240V] 76typ.[AC.240V]
Output characteristics
Output voltage Edc
V 5 12 15 24
Voltage variable range Edc V Fixed Fixed Fixed Fixed
Maximum output current A 3 1.3 1 0.7
Minimum output current A 0 0 0 0
Overvoltage threshold Edc V 5.75min. 13.8min. 17.25min. 27.6min.
Overcurrent threshold A 3.15min. 1.37min. 1.05min. 0.74min.
Voltage
stability
Source effect % 0.4max.[Within the input voltage range]
Load effect % 0.8max.[0 to 100% load]
Temperature effect % 1max.[Ambient temperature: –10 to +50°C]
Drift(Time effect) % 0.4max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
Recovery % ±4max.[50 to 100% sudden load change]
Ripple Ep-p mV 80max. 120max. 120max. 120max.
Ripple noise Ep-p mV 120max. 150max. 150max. 150max.
Start up time ms 200max.(25typ.)/100max.(25typ.)[AC.100/240V] 200max.(40typ.)/100max.(40typ.)[AC.100/240V]
Hold up time ms 13typ./150typ. [AC.100/240V]
Auxiliary functions
Indicator display
No
Overvoltage protection Zenor diode clamp method, output may latch up depending on the condition.
Overcurrent protection Rectangular type, automatic recovery.
Remote ON-OFF No
Remote sensing No
Parallel operation Impossible
Series operation Impossible
Output voltage external variable function No
Standards
Safety standards
UL60950-1, CSA C22.2 No.60950-1(C-UL), EN60950-1(TÜV) approved.
Noise terminal voltage FCC-B, VCCI-B, EN55011-B, EN55022-B meet.
Input harmonics current requirement No
Constructions
External dimensions
mm 22.6 Ч 50Ч 95[HЧ WЧ L]
Weight g 80max.
Mounting method Can be attached to 1 side.
Case material No(PWB Material: CEM3)