Onkyo TX SR607 - Manual (Page 77)

77
Advanced Setup
—Continued
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod) to the UNIVERSAL
PORT jack, you cannot assign any listening mode to
PORT selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Assigning Listening Modes to Input
Sources
1 Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2 Use the Up and Down [ ]/[ ] buttons to
select “5. Listening Mode Preset”, and
then press [ENTER].
The “Listening Mode Preset” menu appears.
3 Use the Up and Down [ ]/[ ] buttons to
select the input source that you want to
set, and then press [ENTER].
The signal format selection menu appears.
For TUNER input selector only “Analog” will be
available.
4 Use the Up and Down [ ]/[ ] buttons to
select the signal format that you want to
set, and then use the Left and Right [
]/
[ ] buttons to select a listening mode.
Only listening modes that can be used with each
input signal format can be selected (see
pages 63–66).
The Last Valid option means that the listening
mode selected last will be used.
5. Listening Mode Preset
1. DVD/BD
2. VCR/DVR
3. CBL/SAT
4. GAME
5. AUX
6. TV/TAPE
7. TUNER
8. CD
9. PORT
5–1. Listening Mode Preset
Analog / PCM
Dolby D/Dolby D +
DTS/DTS HD HR
D.F. 2ch
D.F. Mono Last Valid
Last Valid
Last Valid
Last Valid
Last Valid
—DVD/BD—
Analog / PCM: With this setting, you can specify
the listening mode to be used when an analog
(CD, TV, LD, VHS, MD, turntable, radio, cas-
sette, cable, satellite, etc.) or PCM digital (CD,
DVD, etc.) audio signal is played.
Dolby D/Dolby D +: With this setting, you can
specify the listening mode to be used when a
Dolby Digital or Dolby Digital Plus format digital
audio signal is played (DVD, etc.).
DTS/DTS HD HR: With this setting, you can
specify the listening mode to be used when a DTS
or DTS-HD High Resolution format digital audio
signal is played (DVD, LD, CD, etc.).
D.F. 2ch: Specifies the default listening mode for
2-channel (2/0) stereo sources in a digital format,
such as Dolby Digital or DTS.
D.F. Mono: With this setting, you can specify the
listening mode to be used when a mono digital
audio signal is played (DVD, etc.).
Multich PCM: Specifies the default listening
mode for multichannel PCM sources input via a
HDMI IN, such as DVD-Audio.
Dolby TrueHD: Specifies the default listening
mode for Dolby TrueHD sources, such as Blu-ray
or HD DVD (input via HDMI).
DTS-HD Master Audio: Specifies the default
listening mode for DTS-HD Master Audio
sources, such as Blu-ray or HD DVD (input via
HDMI).
DSD: Specifies the default listening mode for
DSD multichannel sources, such as SACD.
5 When you’ve finished, press the [SETUP]
button.
The setup menu closes.