Onkyo TX SR607 - Manual (Page 103)

103
Troubleshooting
—Continued
• If you still can’t control your iPod, start playback by
pressing your iPod’s Play button. Remote operation
should then be possible.
• Try resetting your iPod.
• Depending on your iPod, some buttons may not work
as expected.
The AV receiver unexpectedly selects your iPod
as the input source
• Always pause iPod playback before selecting a different
input source. If playback is not paused, the Direct
Change function may select your iPod as the input
source by mistake during the transition between tracks.
Can’t record
• On your recorder, make sure the correct input is
selected.
• When the Pure Audio listening mode is selected,
recording is not possible because no video signals are
output. Select another listening mode.
There’s no sound
• Only components connected to analog inputs can be
played in Zone 2.
The sound changes when I connect my
headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio. (Pure Audio listening mode
is not available for North American/Taiwan models.)
The display doesn’t work
• The display is turned off when the Pure Audio listen-
ing mode is selected.
How do I change the language of a multiplex
source
• Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub” (page 73).
The functions don’t work
• To use , you must make an connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 37).
The functions Auto Power On/Standby and
Direct Change don’t work for components
connected via
• These functions don’t work when Zone 2 is turned on.
When performing “Audyssey 2EQ™ Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high”.
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these settings.
1. While holding down the input selector button for the input
source that you want to set, press the [SETUP] button.
2. Use the Left and Right [ ]/[ ] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
• Video Attenuation
This setting can be made for the DVD/BD, VCR/
DVR, CBL/SAT, GAME, or AUX input.
If you have a games console connected to the com-
posite video input, and the picture isn’t very clear,
you can attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
The AV receiver can upconvert component video and composite
video sources for display on a TV connected to the HDMI OUT.
However, if the picture quality of the source is poor, upconver-
sion may make the picture worse or disappear altogether.
In this case, try the following:
1 If the video source is connected to a component
video input, connect your TV to the
COMPONENT VIDEO OUT.
If the video source is connected to a composite video
input, connect your TV to the MONITOR OUT V
2 On the main menu, select “1. Input Assign”, and
then select “1. HDMI Input”.
Select the relevant input selector, and assign it to
“- - - - -” (page 40).
3 On the main menu, select “1. Input Assign”, and
then select “2. Component Video Input”
(page 41):
If the video source is connected to COMPONENT
VIDEO IN1, select the relevant input selector, and
assign it to “IN1”.
If the video source is connected to COMPONENT
VIDEO IN2, select the relevant input selector, and
assign it to “IN2”.
If the video source is connected to composite video input,
select the relevant input selector, and assign it to “- - - - -”.
Recording
Zone 2
Others
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations, severe
interference, noise from an external source, or static elec-
tricity may cause it to lockup. In the unlikely event that this
happens, unplug the power cord from the wall outlet, wait at
least five seconds, and then plug it back in again.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure
that the material will be recorded correctly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
Important Note Regarding Video Playback