Onkyo HT-R490 - Manual (Page 32)

32
Pre-programming remote controller
INPUT SELECTOR
MODE
SLEEP DIMMER DISPLAY
CD TAPE TUNER
D V D VIDEO 1 VIDEO 2
SUR MODE SW MODE AUDIO SEL
TUNER
PRESE T
TV CABLE SATELLITE VCR
STANDBY/ ON
STANDBY/ ON
CH
DISC MUTING
DVD CD TAPE
VOLUME
TV/ VCR
TOP MENU MENU
CH T V VOL
T V VOL
CH SEL
RETURN SETUP
TEST TONE LEVEL
E N T E R
1 2 3
6
9
5
8
0
4
7
MODE
LEVEL
5
RC- 446 M
REMOTE CONTROLLER
Learning a pre-programming code
You can make RC-446M remote controller to operate a product
from other brand than Onkyo by storing the pre-programming
code of the brand in the RC-446M.
1. Find the 2-digit number for the brand name of
the component that you want to operate in the
table on page 33.
2. Turn on the component that you want to operate
(i.e. DVD, satellite tuner, or television).
3. While holding down the MODE button on the
RC-446M that you want to program, press the
LEVEL
5 button, and then release both buttons.
4. Within 30 seconds, enter the 2-digit code
number.
To enable entry of the 2-digit code number, some of the remote
controller keys become the numeric keys with the assignment
as shown in the figure.
5. Press some operation buttons for the component
that you want to operate to check if the system
operates properly.
If the system operates properly, the code is correct. If the
component does not operate properly, return to step 3.
Controlling a DVD player
Buttons with programmed usage and operations are the same as
the operational buttons on page 31.
When entering the code of Onkyo DVD players
There are three SETTING numbers. Choose the SETTING
number according to how you will be using the DVD player.
No. 02/03: These codes are for operating the Onkyo DVD player
by pointing the remote controller directly at it, either because it
does not have an z connector, or it does but you are not using an
z
cable and connecting it. With the initial setting of the
RC-446M, the code is set to 03. If it does not operate properly,
enter 02.
No. 01: This code is for Onkyo DVD players that have an z
connector that you are connecting to the HT-R490 with an z
cable. You will then operate the DVD player by pointing the
remote controller at the remote control sensor on the HT-R490.
With the initial setting of the RC-446M, the code is set to 03.
When the DVD player is connected with z connecter of the
HT-R490, you will need to change the code to 01.
Controlling a TV/VCR/Cable TV/Satellite tuner
1. Press the desired MODE button.
2. Press the STANDBY/ON button to turn on the
device.
3. Press the desired operation button.
TV mode
CH+ : Changes the TV channel upward.
CH– : Changes the TV channel downward.
TV VOL+ : Increases the TV volume.
TV VOL– : Decrease the TV volume.
TV/VCR : Switches the TV/VCR inputs.
VCR mode
CH+ : Changes the received channel upward.
CH– : Changes the received channel downward.
s : Starts playback of videotape.
e : Stops playback, recording, fast forward or rewinding.
f : Fast-forwards the videotape.
d : Rewinds the videotape.
2/8 : Lets playback pause temporarily.
CABLE/SAT mode
CH+ : Changes the received channel upward.
CH– : Changes the received channel downward.
Notes:
• With some brand’s components, some buttons may not work
correctly.
• If more than one code is given in the table, try the code one by
one until you reach the code for your component (i.e. if the
first code does not work, then try the next).