Radio Shack 43-3537 - Manual (Page 5)

5
selected setting and the display shows
H_d]ý H_d]ý H_d]ý H_d]ý
Jof[э7э>_]^ Jof[э7э>_]^ Jof[э7э>_]^ Jof[э7э>_]^
,
H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem
,
H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^
,
H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem
, or
H_d][hýE\\ H_d][hýE\\ H_d][hýE\\ H_d][hýE\\
.
6 740+0) "# 761 "6 #.- "1 0 11 ((
Your phone is preset so you must press TALK
when you lift the handset from the base to
answer a call. With Auto Talk turned on, you
can answer a call by just lifting the handset
from the base. If the handset is away from
the base, you can answer by pressing
TALK ,
any number,
∗∗∗∗
/TONE/
6
, or # /
7
.
1. Lift the handset and hold down CID/
MENU until the menu appears with
7kje 7kje 7kje 7kje
JWba JWba JWba JWba
selected.
2. Press SEL to change the Auto Talk
setting.
Ed Ed Ed Ed
or
E\\ E\\ E\\ E\\
appears indicating the
selected setting.
3. Return the handset to the base (or press
END ) to store the new setting.
6
740+0)
"%
#..'4
"+&1%
#..
"
9
#+6+0)
"1
0
11
((
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Caller
ID information for an incoming call even while
you are using the phone.
1. Lift the handset and hold down CID/
MENU until the menu appears with
7kje 7kje 7kje 7kje
JWba JWba JWba JWba
selected.
2. Press 2 or
9
to move the cursor to
9?:9M0 9?:9M0 9?:9M0 9?:9M0
(Caller ID/Call Waiting).
3. Press SEL to turn the Caller ID/Call
Waiting setting on or off.
Ed Ed Ed Ed
or
E\\ E\\ E\\ E\\
appears indicating the selected setting.
4. Press END and return the handset to the
base to store the new setting.
5
614+0)
";
174
"#
4'#
"%
1&'
You can store your local area code in the
phone’s memory so the area code does not
appear if you receive a local call. If you need
to add or store the area code for a local
number, you can add it afterwards (see
“Adding/Deleting the Area Code” on Page 9).
±
1. Lift the handset and hold down CID/
MENU until the menu appears with
7kje 7kje 7kje 7kje
JWba JWba JWba JWba
selected.
2. Press 3 or
9
to move the cursor to
7h[Wý 7h[Wý 7h[Wý 7h[Wý
9eZ[0 9eZ[0 9eZ[0 9eZ[0
.
3. Press SEL , then enter your three-digit
area code. If you make a mistake,
repeatedly press
∗∗∗∗
/TONE/
6
or # /
7
to
move the cursor over the incorrect digit,
then enter the correct number.
4. Press SEL to store the area code, then
press END or return the handset to the
base to clear the display.
#"
5 '66+0) " 6*' "& +#.+0) "/ 1&'
Your phone is set for tone dialing. If you have
pulse service, change the dialing mode. If
you are not sure which type of service you
have, do this test.
1. Lift the handset, press TALK , and listen
for a dial tone.
2. Press any number other than 0 . ±
If the dial tone stops, you have touch-
tone service. If the dial tone continues,
you have pulse service.
3. Press TALK .
Follow these steps to set the dialing mode.
1. Lift the handset then hold down CID/
MENU until the menu appears with
7KJEý 7KJEý 7KJEý 7KJEý
J7BA J7BA J7BA J7BA
selected.
2. Press 4 or
9
to move the cursor to
:_Wb0 :_Wb0 :_Wb0 :_Wb0
,
then press SEL to change the dialing
mode setting.
Jed[ Jed[ Jed[ Jed[
or
Fkbi[ Fkbi[ Fkbi[ Fkbi[
appears,
indicating the selected setting.
3. Return the handset to the base (or press
END ) to store the new setting.
5 '.'%6+0) " 6*' ". #0)7#)'
You can set the display language to either
English or French.
1. Lift the handset and hold down CID/
MENU until the menu appears with
7kje 7kje 7kje 7kje
JWba JWba JWba JWba
selected.
2. Press 5 or
9
to move the cursor to
BWd]kW][ BWd]kW][ BWd]kW][ BWd]kW][
.
3. Press SEL to select
;d] ;d] ;d] ;d]
(English) or
(French).
4. Return the handset to the base or press
END to store the new setting.
/#-+0)"#0&"
4'%'+8+0)"%#..5
The handset window has plastic film on it to
protect it during shipment. Carefully peel off
the film before using your phone.
To make a call, lift the handset and press
TALK .
JWba JWba JWba JWba
and the current volume setting
appear on the handset’s display, and the
CHARGE/IN USE indicator on the base
lights. Dial the number. The number appears
on the handset as you dial, then the call’s
elapsed time appears. To end a call, place
the handset on the base or press
END .
± ± ± ±
"016'"
± ± ± ±
"
Storing Your Area Code
If an area code is already stored, it appears on
the display after you hold down CID/MENU.
Press DEL/CH three times to delete the area
code. Then enter your area code.
Setting the Dialing Mode
If your phone system requires that you dial an
access code (9, for example) before you dial an
outside number, do not dial the access code
either.
# "+/2146#06" #
In some areas, the area code is necessary even
for a local call. If you live in such an area, do not
store the area code.