Radio Shack 43-3537 - Manual (Page 3)

3
There may be a remote risk of electric
shock from lightning.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
$
#66'4;
"5
#('6;
"+
05647%6+105
"
To reduce the risk of fire or injury, read and
follow these instructions
1. Use only the appropriate type and size
battery pack specified in the instruction
manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
3. Do not open or mutilate the battery pack.
Released electrolyte is corrosive and
may cause damage to the eyes or skin. It
may be toxic if swallowed.
4. Exercise care in handling the battery
pack in order not to short it with
conducting materials such as rings,
bracelets, and keys. The battery or
conductor may overheat and cause
burns.
5. Charge the battery pack provided or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
5#8'"6*'5'"
+05647%6+105
+056#..#6+10
Cordless phones require AC power to
operate. When the power is off, you cannot
make or receive calls using your phone. You
should also have a phone that does not need
AC power to operate (not a cordless phone),
so you can still make and receive calls if
there is an AC power failure.
#"
Before using your phone, carefully peel the
protective film off the display. The film
protects the handset window during shipment
and is not necessary for use.
5
'.'%6+0)
"
#
".
1%#6+10
You can place the phone’s base on a desk or
table, or mount it on a standard wall plate or
directly on a wall. Select a location that is:
• near an accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or filing
cabinets, wireless intercoms, alarms,
and room monitors
• away from other cordless phones
The base’s location affects the handset’s
range. If you have a choice of several
locations, try each to see which provides the
best performance.
.#
Your telephone connects directly to a
modular telephone line jack. If your telephone
wiring does not have a modular jack, you can
update the wiring yourself using jacks and
adapters (available at your local RadioShack
store), or have the telephone company
update the wiring for you. You must use
compatible modular jacks that are compliant
with Part 68 of FCC Rules.
±
1
0
"
#
"&
'5-
"6
12
1. Plug one end of the
supplied long
modular cord into
the
TEL LINE jack on
the back of the base.
2. Plug the modular
cord’s other end into
a modular phone
line jack.
3. Insert the supplied
AC adapter’s barrel
plug into the
DC IN
9V jack on the back
of the base.
4. Route the adapter’s
cord through the strain relief slot on the
base, then plug the adapter into a
standard AC outlet.
5. Lift the base’s antenna to a vertical
position.
1 0 " # "9 #.. "2 .#6'
1. Plug one end of the supplied short
modular cord into the TEL LINE jack on
the back of the base. Then insert the
supplied AC adapter’s barrel plug into
the
DC IN 9V jack on the back of the
base.
2. Route the adapter and modular cords
through the grooves on the bottom of the
base.
3. Plug the short modular cord into the wall
plate jack, then align the base’s keyhole
slots with the wall plate studs and slide
the base down to secure it.
4. Plug the adapter into a standard AC
outlet.
# "+/2146#06" #
• When AC power is lost, the phone loses the
security access-protection code con-nection
between the base and the hand-set. When
power is restored, put the handset on the
base briefly to restore this connection so you
can use the handset.
• Your phone operates on standard radio
frequencies as allocated by the FCC.
• It is possible for other radio units operating
nearby on similar frequencies to
unintentionally intercept your conversation or
cause interference. This possible lack of
privacy can occur with any cordless phone.
.
"%#76+10"
.
•You must use a Class 2 power
source that supplies 9V DC and
delivers at least 210 mA. Its center
tip must be set to positive and its plug must fit
the phone's DC IN 9V jack. The supplied
adapter meets these specifications. Using an
adapter that does not meet these
specifications could damage the phone or the
adapter.
• Always connect the AC adapter to the phone
before you connect it to AC power. When you
finish, disconnect the adapter from AC power
before you disconnect it from the phone.
!
± ± ± ±
"016'"
± ± ± ±
"
The USOC number of the jack to be installed is
RJ11C (or RJ11W for a wall plate jack).
TEL LINE
DC IN 9V