Radio Shack 2.4 GHz 2-Line Digital Spread Spectrum Cordless Phone with Call Waiting/Caller ID - Manual (Page 14)

14 Installation
Note: The phone exits setting mode if a call
or page is received, or if you press
LINE 1 or
LINE 2 .
ADJUSTING THE RINGER
The phone lets you control its base and
handset ringer volume separately. You can
choose from a high or low ringer setting or
turn the ringer off for the base and the hand-
set.
On the Handset
In the standby mode, press DEL / VOL to set
the handset’s ringer volume. The display
shows
H_d][h H_d][h H_d][h H_d][h >_]^ >_]^ >_]^ >_]^
or
H_d][h H_d][h H_d][h H_d][h Bem Bem Bem Bem
.
You can also turn off the ringer. In the stand-
by mode, press and hold
DEL / VOL until the
phone beeps and
H_d][h H_d][h H_d][h H_d][h E\\ E\\ E\\ E\\
appears. When
you place the handset face-up on the base,
2H_d][hýE\\4 2H_d][hýE\\4 2H_d][hýE\\4 2H_d][hýE\\4
appears.
You can still make or receive a call even
when the ringer is turned off. When you have
an incoming call, the base unit (if you have
not set
RING VOL to OFF ) and any other
phone connected to the same line rings, and
â9Wbbá â9Wbbá â9Wbbá â9Wbbá
appears on the handset’s display.
To turn the ringer back on, simply press DEL /
VOL . The ringer is restored at the
H_d][h H_d][h H_d][h H_d][h >_]^ >_]^ >_]^ >_]^
setting.
On the Base
Set RING VOL on the back of the base to HI ,
LO , or OFF for each line ( L1 and L2 ). With
RING VOL set to OFF , the base’s ringer does
not sound when a call is received, but the
handset (when it is off the base with the ring-
er not turned off) and any other phone con-
nected to the same line still ring.
SETTING AUTO TALK
Your phone is preset so you must press LINE
1 or LINE 2 to answer a call. With auto talk
turned on, you can answer a call by lifting the
handset from the base (or any key on the
handset if the handset is away from the
base).
Note: Auto talk is set for each line separate-
ly. For example, when you turn auto talk on
for Line 1 only, you must press
LINE 2 to an-
swer a call on line 2.
Follow these steps to turn auto talk on or off.
1. Lift the handset and hold down CID /
HOLD until
9Wbb[h 9Wbb[h 9Wbb[h 9Wbb[h ?: ?:?: ?: I[jkf I[jkf I[jkf I[jkf
appears on the
display with the pointer at
B_d[ B_d[ B_d[ B_d[ ''''
.
2. Use
∗∗∗∗
/ TONE /
6 6 6 6
or # /
7 7 7 7
to select
B_d[ B_d[ B_d[ B_d[ ''''
or
B_d[ B_d[ B_d[ B_d[ ((((
. Then press CONF /
9 9 9 9
.
3. A menu appears with
7kje 7kje 7kje 7kje JWba JWba JWba JWba
selected.
Press SELECT / CH to change the setting.
Ed Ed Ed Ed
or
E\\ E\\ E\\ E\\
appears indicating the selected
setting.
4. Press CID / HOLD and return the handset
to the base.
SETTING CALLER ID/CALL
WAITING
If you have Call Waiting and Caller ID ser-
vice, you can set the phone to show Caller ID
information for an incoming call even while
you are already on the phone.
Note: Caller ID/Call Waiting function is set
for each line separately.
1. Lift the handset and hold down CID /
HOLD until
9Wbb[h 9Wbb[h 9Wbb[h 9Wbb[h ?: ?:?: ?: I[jkf I[jkf I[jkf I[jkf
appears on the
display with
B_d[ B_d[ B_d[ B_d[ ''''
selected.
2. Use
∗∗∗∗
/ TONE /
6 6 6 6
or # /
7 7 7 7
to select
B_d[ B_d[ B_d[ B_d[ ''''
or
B_d[ B_d[ B_d[ B_d[ ((((
. Then press CONF /
9 9 9 9
.